- 您现在的位置：买卖IC网 > PDF目录378649 > lCL8052CDD (Intersil Corporation) Precision 4 1/2 Digit, A/D Converter PDF资料下载
参数资料
| 型号： | lCL8052CDD |
| 厂商： | Intersil Corporation |
| 英文描述： | Precision 4 1/2 Digit, A/D Converter |
| 中文描述： | 精密4 1 / 2位，A / D转换 |
| 文件页数： | 9/19页 |
| 文件大小： | 168K |
| 代理商： | LCL8052CDD |
3-42
once and only once for each measurement cycle starting
101/11 pulses after the end of the full measurement cycle.
Digit 5 (MSD) goes high at the end of the measurement
cycle and stays on for 201/21 counts. In the center of this
digit pulse (to avoid race conditions between changing BCD
and digit drives) the first STROBE pulse goes negative for
1
/
2
clock pulse width. Similarly, after Digit 5, Digit 4 goes
high (for 200/20 clock pulses) and 100/10 pulses later the
STROBE goes negative for the second time. This continues
through Digit 1 (LSD) when the fifth and last STROBE pulse
is sent. The digit drive will continue to scan (unless the
previous signal was over-range) but no additional STROBE
pulses will be sent until a new measurement is available.
Busy (Pin 28)
BUSY goes high at the beginning of signal integrate and
stays high until the first clock pulse after zero-crossing (or
after end of measurement in the case of an OVER-RANGE).
The internal latches are enabled (i.e., loaded) during the first
clock pulse after BUSY and are latched at the end of this
clock pulse. The circuit automatically reverts to auto-zero
when not BUSY so it may also be considered an A-Z signal.
A very simple means for transmitting the data down a single
wire pair from a remote location would be to AND BUSY with
clock and subtract 10,001/1,001 counts from the number of
pulses received - as mentioned previously there is one “NO-
count” pulse in each Reference Integrate cycle.
Over-Range (Pin 4)
This pin goes positive when the input signal exceeds the
range (20,000/2,000) of the converter. The output F-F is set
at the end of BUSY and is reset to zero at the beginning of
Reference Integrate in the next measurement cycle.
Under-Range (Pin 13)
This pin goes positive when the reading is 9% of range or
less. The output F-F is set at the end of BUSY (if the new
reading is 1800/180 or less) and is reset a the beginning of
Signal Integrate of the next reading.
Polarity (Pin 3)
This pin is positive for a positive input signal. It is valid even for a
zero reading. In other words, +0000 means the signal is posi-
tive but less than the least significant bit. The converter can be
used as null detector by forcing equal (+) and (-) readings. The
null at this point should be less than 0.1 LSB. This output
becomes valid at the beginning of Reference Integrate and
remains correct until it is revalidated for the next measurement.
Digit Drives (Pins 19, 24, 25, 26, and 27)
Each digit drive is a positive-going signal which lasts for
200/20 clock pulses. The scan sequence is D
5
(MSD), D
4
,
D
3
, D
2
, and D
1
(LSD). All five digits are scanned even when
operating in the 3
1
/
2
digit mode, and this scan is continuous
unless and OVER-RANGE occurs. Then all Digit drives are
blanked from the end of the STROBE sequence until the
beginning of Reference Integrate, at which time D
5
will start
the scan again. This gives a blinking display as a visual
indication of OVER-RANGE.
BCD (Pins 20, 21, 22 and 23)
The Binary coded decimal bit B
8
, B
4
, B
2
, and B
1
are positive
logic signals that go on simultaneously with the Digit driver.
FIGURE 5. TIMING DIAGRAM FOR OUTPUTS
AUTO
ZERO
COUNTS
FULL MEASUREMENT CYCLE
40,002/4,002 COUNTS
10,001
INTEGRATOR
OUTPUT
BUSY
SIGNAL
INTEG.
COUNTS
10,000
REFERENCE
INTEGRATE
COUNTS MAX
20,001 / 2,001
D
5
D
4
D
3
D
2
D
1
AUTO ZERO
DIGIT SCAN
FOR OVER-RANGE
SIGNAL
INTEGRATE
REFERENCE
INTEGRATE
D
1
D
2
D
3
D
4
D
5
FIRST D
5
OF AZ AND REF INT
ONE COUNT LONGER
STROBE
1000
/100 COUNTS
DIGIT SCAN
FOR OVER-RANGE
EXPANDED SCALE BELOW
OVER-RANGE
WHEN APPLICABLE
UNDER-RANGE
WHEN APPLICABLE
ICL8052/ICL71C03, ICL8068/ICL71C03
相关PDF资料 |
PDF描述 |
|---|---|
| LDA101 | Solid State Current Sensors |
| LDA101S | Solid State Current Sensors |
| LDA101STR | Solid State Current Sensors |
| LDA200 | Solid State Current Sensors |
| LDA200S | Solid State Current Sensors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LCL8068ACJD | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Precision 4 1/2 Digit, A/D Converter |
| LC-LA1233P | 功能描述:密封铅酸电池 12V 33AH BOLT/NUT RoHS:否 制造商:CSB 输出电压:12 V 容量: 大小: 端接类型:Faston Tab |
| LC-LA1233PG | 制造商:Panasonic Industrial Devices 功能描述: |
| LC-LC/5M | 制造商:Enhance Technology 功能描述:5 METER FIBRE CHANNEL OPTICAL CABLE - Bulk |
| LCLC09DYE1 | 制造商:FibreFab 功能描述: 制造商:OPTRONICS 功能描述:PATCHCORD 1M LC-LC 9/125 制造商:OPTRONICS 功能描述:PATCHCORD, 1M, LC-LC, 9/125M |
发布紧急采购，3分钟左右您将得到回复。