- 您现在的位置：买卖IC网 > PDF目录19323 > LDS8161-002-T2 (IXYS)IC LED DRIVER WHIT BCKLGT 16WQFN PDF资料下载
参数资料
| 型号： | LDS8161-002-T2 |
| 厂商： | IXYS |
| 文件页数： | 15/22页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER WHIT BCKLGT 16WQFN |
| 标准包装： | 1 |
| 系列： | LED-Sense™, PowerLite™ |
| 拓扑： | 高端，线性（LDO），PWM |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 电源电压： | 2.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | LDS8161-002-T2-6 |
LDS8161/41
disabled via the I C interface by addressing register
Unused LED Channels
For applications with less than six (8161) or four
(8141) LEDs, the unused LED channels can be
2
03h with data that represents the desired
combination of LEDs turned ON/OFF (see Table 1).
The LDS8161/41 unused LED outputs can be left
open.
Parallel-Connected LED Channels for Higher
level to shutdown V IN power to prevent possible
damage to the LED. The combined series resistance
of the LED (typically ~ 10 ? or more) and additional
board series resistance will result in current limiting
but not sufficient to insure no damage to low power
LEDs.
Besides the power-up diagnostic sequence, the user
can re-initiate a diagnostic command at any time by
setting bit 5 of the Digital Test Modes Register, 19h,
to HIGH.
Current LEDs
The LDS8161/41
restores LED current
to
In higher power LED applications requiring more than
31.875 mA DC current, LED driver channels can be
connected in parallel.
For example, ? watt, 150 mA LEDs can be driven
with the LDS8161 by paralleling all 6 channels with
25 mA per channel. Likewise, the LDS8141 can drive
up to 127.5 mA by connecting all 4 channels in
parallel at the maximum 31.875 mA per channel.
LED short/open protection
The LDS8161/41 runs a LED short/open diagnostic
routine upon the power up sequence. It detects both
LED pins shorted to ground and LED pins that are
open or shorted to V IN (fault conditions).
The results for short to GND detection are stored in
Diagnostics Register 1Ch. Bits from bit 5 to bit 0
indicate a short status as bit = 1 for LEDC2 - LEDA1
respectively. A short to GND is detected, if the
measured LED pin voltage is less than ~ 0.14 V
independent of the programmed LED current. Every
channel, detected as shorted, is disabled
Test results for open or short to V IN LED pins are
stored in Diagnostics Register 1Dh, Bits from bit 5 to
bit 0 represent LEDC2 - LEDA1 respectively with bit
= 1 indicates fault condition at this particular LED pin.
An open LED pin fault causes no harm in the
LDS8161/41 or the LED as the high side driver has
no current path from V IN or GND. Therefore, the fault
detection status indicates only in the 1Dh diagnostic
register, and no further action is required.
In the case of an LED directly shorted to V IN , the full
V IN voltage will be connected to the LED and current
can flow independent of the LDS8161/41 LED driver
circuit directly to GND. The LDS8161/41 will detect
the fault and indicate the status in Register 1Dh,
however further action needs taken at the system
programmed value at channels with detected shorts
to GND after the fault condition is removed.
Over-Temperature Protection
If the die temperature exceeds +150°C, the driver will
enter shutdown mode. The LDS8161/41 requires
restart after die temperature falls below 130°C.
LED Selection
If the power source is a Li-ion battery, LEDs with V F =
1.9 V - 3.3 V are recommended to achieve highest
efficiency performance and extended operation on a
single battery charge.
External Components
The driver requires one external 1 μF ceramic capa-
citors (C IN ) X5R or X7R type.
CONFIGURATION MODES
The LDS8161/41 allows the option to choose special
operating modes overwriting content of Configuration
Register 1Eh (see Table 2).
Bit 1 allows bypass soft start / ramp down if fast
raising/falling LED current required.
Bit 2 allows disable LED temperature compensation if
desired.
The LDS8161/41 also provides the option for using
an external remote temperature-sensing diode device
such as a 2N3904. To use this option the diode
anode should be connected to channel LEDA1. The
cathode connected to GND. In this case, channel
LEDA1 should be disabled via register 03h and it
cannot operate as an LED current source.
Bits 0, 3, 4, 5, 6, and 7 of the Configuration Register
1Eh are for factory use only and should be set to 0 or
the user should use the power-on-reset values.
? 2009 IXYS Corp.
Characteristics subject to change without notice
15
Doc. No. 8141/61_DS, Rev. N1.0
相关PDF资料 |
PDF描述 |
|---|---|
| R24P23.3S/X2/R8 | CONV DC/DC 2W 24VIN 3.3VOUT |
| EP1AGX90EF1152C6N | IC ARRIA GX FPGA 90K 1152FBGA |
| HSC43DRTH-S93 | CONN EDGECARD 86POS DIP .100 SLD |
| TACR685K010X | CAP TANT 6.8UF 10V 10% 0805 |
| VJ1206A200KBBAT4X | CAP CER 20PF 100V 10% NP0 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LDS85-750 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LDS8620-002-T2 | 功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LDS8621-002-T2 | 功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LDS8621002-T2-960 | 功能描述:IC LED DRIVER FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| LDS8640-002-T3 | 功能描述:LED照明驱动器 400mA Dual Output Flash/Lamp Drvr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。