- 您现在的位置：买卖IC网 > PDF目录80327 > LM5067SDX-1 (NATIONAL SEMICONDUCTOR CORP) 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10 PDF资料下载
参数资料
| 型号： | LM5067SDX-1 |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10 |
| 封装： | LLP-10 |
| 文件页数： | 4/24页 |
| 文件大小： | 690K |
| 代理商： | LM5067SDX-1 |
30030931
FIGURE 4. Gate Control
Current Limit
The current limit threshold is reached when the voltage across
the sense resistor R
S (SENSE to VEE) reaches 50 mV. In the
current limiting condition, the GATE voltage is controlled to
limit the current in MOSFET Q1. While the current limit circuit
is active, the fault timer is active as described in the Fault
Timer & Restart section. If the load current reduces below the
current limit threshold before the end of the Fault Timeout
Period, the LM5067 resumes normal operation. For proper
operation, the R
S resistor value should be no larger than 100
m
.
Circuit Breaker
If the load current increases rapidly (e.g., the load is short-
circuited) the current in the sense resistor (R
S) may exceed
the current limit threshold before the current limit control loop
is able to respond. If the current exceeds approximately twice
the current limit threshold (100 mV/R
S), Q1’s gate is quickly
pulled down by the 110 mA pull-down current at the GATE
pin, and a Fault Timeout Period begins. When the voltage
across R
S falls below 100 mV the 110 mA pull-down current
at the GATE pin is switched off, and the gate voltage of Q1 is
then determined by the current limit or the power limit func-
tions. If the TIMER pin reaches 4.0V before the current limiting
or power limiting condition ceases, Q1 is switched off by the
2.2 mA pull-down current at the GATE pin as described in the
Fault Timer & Restart section.
Power Limit
An important feature of the LM5067 is the MOSFET power
limiting. The Power Limit function can be used to maintain the
maximum power dissipation of MOSFET Q1 within the device
SOA rating. The LM5067 determines the power dissipation in
Q1 by monitoring its drain-source voltage (OUT to SENSE),
and the drain current through the sense resistor (SENSE to
VEE). The product of the current and voltage is compared to
the power limit threshold programmed by the resistor at the
PWR pin. If the power dissipation reaches the limiting thresh-
old, the GATE voltage is modulated to reduce the current in
Q1, and the fault timer is active as described in the Fault Timer
& Restart section.
Fault Timer & Restart
When the current limit or power limit threshold is reached
during turn-on or as a result of a fault condition, the gate-to-
source voltage of Q1 is modulated to regulate the load current
and power dissipation in Q1. When either limiting function is
active, an 85 A fault timer current source charges the exter-
nal capacitor (C
T) at the TIMER pin as shown in Figure 6
(Fault Timeout Period). If the fault condition subsides before
the TIMER pin reaches 4.0V, the LM5067 returns to the nor-
mal operating mode and C
T is discharged by the 2.5 A
current sink. If the TIMER pin reaches 4.0V during the Fault
Timeout Period, Q1 is switched off by a 2.2 mA pull-down
current at the GATE pin. The subsequent restart procedure
depends on which version of the LM5067 is in use.
The LM5067-1 latches the GATE pin low at the end of the
Fault Timeout Period, and C
T is discharged by the 2.5 A fault
current sink. The GATE pin is held low until a power up se-
quence is externally initiated by cycling the input voltage
(V
SYS), or momentarily pulling the UVLO/EN pin within 2.5V
of VEE with an open-collector or open-drain device as shown
in Figure 5. The voltage across C
T must be <0.3V for the
restart procedure to be effective.
30030932
FIGURE 5. Latched Fault Restart Control
The LM5067-2 provides an automatic restart sequence which
consists of the TIMER pin cycling between 4.0V and 1.25V
seven times after the Fault Timeout Period, as shown in Fig-
ure 6. The period of each cycle is determined by the 85 A
charging current, and the 2.5 A discharge current, and the
value of the capacitor C
T. When the TIMER pin reaches 0.3V
during the eighth high-to-low ramp, the 52 A current source
at the GATE pin turns on Q1. If the fault condition is still
present, the Fault Timeout Period and the restart cycle repeat.
www.national.com
12
LM5067
相关PDF资料 |
PDF描述 |
|---|---|
| LS4601-7ERD1TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4601-7ERD5TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4001-7EPD2B2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4001-7EPTB2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS4001-7ERD2B2 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM5068 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:NEGATIVE VOLTAGE HOT SWAP CONTROLLER |
| LM5068EVAL | 功能描述:电源管理IC开发工具 LM5068 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM5068EVAL/NOPB | 功能描述:EVALUATION BOARD FOR LM5068 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| LM5068MM-1 | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM5068MM-1/MMX-1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Negative Voltage Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。