- 您现在的位置：买卖IC网 > PDF目录69005 > LM96080CIMT-NOPB (NATIONAL SEMICONDUCTOR CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 PDF资料下载
参数资料
| 型号： | LM96080CIMT-NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| 封装： | ROHS COMPLIANT, PLASTIC, TSSOP-24 |
| 文件页数： | 7/30页 |
| 文件大小： | 600K |
| 代理商： | LM96080CIMT-NOPB |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
6.0 LAYOUT AND GROUNDING
Analog inputs will provide best accuracy when referred to the
AGND pin or a supply with low noise. A separate, low-
impedance ground plane for analog ground, which provides
a ground point for the voltage dividers and analog compo-
nents, will provide best performance but is not mandatory.
Analog components such as voltage dividers should be lo-
cated physically as close as possible to the LM96080.
The power supply bypass, a parallel combination of 10
μF
(electrolytic or tantalum) and 0.1
μF (ceramic) bypass capac-
itors connected between V+, pin 9, and ground, should also
be located as close as possible to the LM96080.
7.0 FAN INPUTS
Inputs are provided for signals from fans equipped with
tachometer outputs. These are logic-level inputs set accord-
ing to the Fan Tach Pulse Inputs in the Electrical Character-
istic table. Signal conditioning in the LM96080 accommo-
dates the slow rise and fall times typical of fan tachometer
outputs. The maximum input signal range is 0 to +5.5V. In the
event these inputs are supplied from fan outputs which ex-
ceed 0 to +5.5V, either resistive division or diode clamping
must be included to keep inputs within an acceptable range.
R2 is selected so that it does not develop excessive error
voltage due to input leakage. R1 is selected based on R2 to
provide a minimum input of 2V and a maximum of 5.5V. R1
should be as low as possible to provide the maximum possible
input up to 5.5V for best noise immunity. Alternatively, use a
shunt reference or zener diode to clamp the input level.
If fans can be powered while the power to the LM96080 is off,
the LM96080 inputs must be protected to meet the ABSO-
LUTE MAXIMUM RATINGS section. In most cases, open
collector outputs with pull-up resistors inherently limit this cur-
rent. If this maximum current could be exceeded, either a
larger pull up resistor should be used or resistors connected
in series with the fan inputs.
The Fan Inputs gate an internal 22.5 kHz oscillator for one
period of the Fan signal into an 8-bit counter (maximum count
= 255). The default divisor is set to 2 (choices are 1, 2, 4, and
8) providing a nominal count of 153 for a 4400 RPM fan with
two pulses per revolution. Typical practice is to consider 70%
of normal RPM a fan failure, at which point the count will be
219.
Determine the fan count according to:
For example, if the frequency of the tachometer were 150 Hz,
the RPM would be 4,500 [RPM = (freq) × (60 seconds/min) /
(2 pulses/revolution) ]. Since the default divisor is 2, the count
would be 150 according to the equation above.
Note that Fan 1 and Fan 2 Divisors are programmable via the
Fan Divisor/RST_OUT/OS Register (address 05h).
FAN1 and FAN2 inputs can also be programmed to be level
sensitive interrupt inputs.
Fans that provide only one pulse per revolution would require
a divisor set twice as high as fans that provide two pulses,
thus maintaining a nominal fan count of 153. Therefore, the
divisor should be set to 4 for a fan that provides 1 pulse per
revolution with a nominal RPM of 4400.
30070112
(a) Fan with Tach Pull-Up to +5V
30070113
(b) Fan with Tach Pull-Up to +12V, or Totem-Pole Output and Resistor Attenuator
15
www.national.com
LM96080
相关PDF资料 |
PDF描述 |
|---|---|
| LMX1602TMX/NOPB | PLL FREQUENCY SYNTHESIZER, 1100 MHz, PDSO16 |
| LMX2324TM/NOPB | PLL FREQUENCY SYNTHESIZER, 2000 MHz, PDSO16 |
| LMX2324MWC | PLL FREQUENCY SYNTHESIZER, 2000 MHz, UUC |
| LMX2324TMX/NOPB | PLL FREQUENCY SYNTHESIZER, 2000 MHz, PDSO16 |
| LMX2324MDC | PLL FREQUENCY SYNTHESIZER, 2000 MHz, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM96080CIMT-NOPB1 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:System Hardware Monitor with 2-Wire Serial Interface |
| LM96080CIMTX/NOPB | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM96080CIMTX-NOPB2 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:System Hardware Monitor with 2-Wire Serial Interface |
| LM96080EB/NOPB | 制造商:Texas Instruments 功能描述:SYSTEM HARDWARE MONITOR WITH 2-WIRE SERI - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:BOARD EVAL FOR LM96080 制造商:Texas Instruments 功能描述:LM96080 EVAL BRD |
| LM96-1/2-LENS-KIT | 制造商:NSC 制造商全称:National Semiconductor 功能描述:LM9648 Color CMOS Image Sensor SXGA 18 FPS |
发布紧急采购，3分钟左右您将得到回复。