参数资料
| 型号： | LT1619ES8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR PWM CM 8-SOIC |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 占空比： | 92% |
| 电源电压： | 1.9 V ~ 18 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 是 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1328 (CN2011-ZH PDF) |
LT1619
OPERATIO
The LT1619 is a fixed frequency current mode switching
regulator PWM controller that can be used in boost, SEPIC
or flyback modes. The device operates from an input
supply range of 1.9V to 18V, and has a separate supply pin
(DRV) for the gate driver. The DRV pin can be bootstrapped
to V OUT for additional gate enhancement in low voltage
applications like 3.3V to 5V boost converters, or con-
nected to the input supply for higher voltage inputs.
To best understand operation of the LT1619, please refer
to Figure 2, the Block Diagram. The gate drive circuit turns
on the external MOSFET at the trailing edge of oscillator
output signal CLK. MOSFET current is sensed with an
external resistor (R SENSE of Figure 1). A leading edge
blanking circuit disables the current sense amplifier for
280ns immediately following switch turn-on, preventing
gate charging current from prematurely tripping the PWM
comparator. A slope compensating ramp, derived from
the oscillator, is added to the current sense output. The
driver turns off the MOSFET when this sum exceeds the
error amplifier output V C . The switch current is limited
with a separate comparator. The compensating ramp is a
progressive nonlinear function of the operating duty ratio
whereas the current limit does not vary with the duty ratio.
Error amplifier output V C determines the peak switch cur-
rent required to regulate the output voltage. V C can be
considered a measure of output current. At heavy loads,
V C is in its upper range. Average and peak inductor cur-
discharges the output capacitor, causing the output volt-
age to decrease. As V OUT decreases, V C increases. As V C
increases above V B , switching action begins, delivering
power to the output. The switch current sense threshold is
about 10mV in this V C region. If the output load remains
light, the output voltage will rise and V C will fall, causing
the converter to idle again. This is known as Burst Mode
operation. The burst frequency depends on input voltage,
output voltage, inductance and output capacitance. Out-
put voltage ripple during Burst Mode operation is usually
higher than when the converter is switching continuously.
Burst Mode operation increases light load efficiency be-
cause it delivers more energy per clock cycle than possible
with discontinuous mode operation and extremely low
peak switch current, allowing fewer switching cycles to
maintain a given output. IC supply current therefore be-
comes a small fraction of the total input current.
Setting Output Voltage
The output voltage of the LT1619 is set with resistive
divider R1 and R2 connected from the output to ground as
detailed in Figure 3. The divider tap is tied to the device FB
pin. Current through R2 should be significantly higher
than the FB pin bias current of 25nA. With R2 = 10k, the
input bias current of the error amplifier is 0.02% of the
current in R2.
V O
( )
V O = 1.24V 1 + R1
( )
V O
rents are high. In this range, the inductor tends to run in
continuous conduction mode (CCM), where current is al-
ways flowing in the inductor. As load current decreases,
average and peak inductor current decreases. When the
LT1619
FB
R1
R2
1.24
R2
R1 = R2 –1
average inductor current falls below 1/2 of the peak-to-peak
inductor current ripple, the converter enters discontinu-
ous conduction mode (DCM), where current in the induc-
tor reaches zero sometime during the discharge phase.
Further reduction in output current moves V C towards its
lower operating range, decreasing inductor current. Hys-
teretic comparator A1 determines if V C is too low for the
LT1619 to operate efficiently. As V C falls below the trip
voltage VB, A1’s output goes high, turning off all blocks
except the error amplifier, A1 and A2. The LT1619 enters
the idle state and switching stops. The device draws just
140 μ A from the input in the idle state. Output load current
1619 F03
Figure 3. Feedback Resistive Divider
Synchronization and Shutdown
The S/S pin (Pin 1) can be used to synchronize the
oscillator to an external source. The S/S pin is tied to the
input (V IN > 1.9V) for normal operation. The oscillator in
the LT1619 can be externally synchronized by driving the
S/S pin with a pulse train with an amplitude of at least 1V.
The maximum allowable rise time is a function of the
pulse amplitude, as shown in Table 1. Rise times equal to
1619fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| ABC13DRXI-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| ABC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| LTC3851EUD#PBF | IC REG CTRLR BUCK PWM CM 16-QFN |
| RCA24DTAD | CONN EDGECARD 48POS R/A .125 SLD |
| RCA28DRMS | CONN EDGECARD 56POS .125 SQ WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1620 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Rail-to-Rail Current Sense Amplifier |
| LT1620CGN | 功能描述:IC AMP R-R CURRENT SENSE 16-SSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1620CGN#PBF | 功能描述:IC AMP R-R CURRENT SENSE 16-SSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LT1620CGN#TR | 功能描述:IC AMP CURRENT SENSE R-R 16SSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| LT1620CGN#TRPBF | 功能描述:IC AMP R-R CURRENT SENSE 16-SSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
发布紧急采购，3分钟左右您将得到回复。