- 您现在的位置：买卖IC网 > PDF目录79915 > LT1871IMS-7#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LT1871IMS-7#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | PLASTIC, MSOP-10 |
| 文件页数： | 14/32页 |
| 文件大小： | 461K |
| 代理商： | LT1871IMS-7#TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC1871-7
21
18717fc
APPLICATIONS INFORMATION
The component chosen is a 6.8μH inductor made by
Cooper (part number DR127-6R8) which has a satura-
tion current of greater than 13.3A.
5. Because the duty cycle is 81%, the maximum SENSE
pin threshold voltage is reduced from its low duty cycle
typical value of 150mV to approximately 115mV. In ad-
dition, we need to apply a worst-case derating factor
to this SENSE threshold to account for manufacturing
tolerances within the IC. Finally, the nominal current
limit value should exceed the maximum load current
by some safety margin (in this case 50%). Therefore,
the value of the sense resistor is:
RSENSE = 0.8 VSENSE(MAX)
1–DMAX
1+ 0.4
2
1.5 IO(MAX)
= 0.8 0.115 1– 0.81
1.2 1.5 1.5
= 6.5m
A 1W, 5mΩ resistor is used in this design.
6. The MOSFET chosen is a Vishay/Siliconix Si7370DP,
which has a BVDSS of greater than 60V and an RDS(ON)
of less than 13mΩ at a VGS of 6V.
7. The diode for this design must handle a maximum DC
output current of 1.5A and be rated for a minimum
reverse voltage of VOUT, or 42V. A 3A, 60V diode from
Diodes Inc. (B360B) is chosen.
8. The output capacitor usually consists of a high valued
bulk C connected in parallel with a lower valued, low
ESR ceramic. Based on a maximum output ripple voltage
of 1%, or 50mV, the bulk C needs to be greater than:
COUT
IOUT(MAX)
0.01 VOUT f
=
1.5
0.01 42 250k
= 14μF
The RMS ripple current rating for this capacitor needs
to exceed:
IRMS(COUT) IO(MAX)
VO –VIN(MIN)
VIN(MIN)
=
1.5 42 – 8
8
= 3.09A
To satisfy the low ESR, high frequency decoupling
requirements, two 10μF, 50V, X5R ceramic capacitors
are used (TDK part number C5750X5R1H106M). In
parallel with these, two 68μF, 100V electrolytic ca-
pacitors are used (Sanyo part number 100CV68FS).
Check the output ripple with a single oscilloscope
probe connected directly across the output capacitor
terminals, where the HF switching currents ow.
9. The choice of an input capacitor for a boost converter
depends on the impedance of the source supply and
the amount of input ripple the converter will safely
tolerate. For this particular design and lab setup a
560μF, 50V Sanyo electrolytic (50MV560AXL), in
parallel with two 10μF, 100V TDK ceramic capacitors
(C5750X5R1H106M) is required (the input and return
lead lengths are kept to a few inches, but the peak input
current is close to 10A!). As with the output node,
check the input ripple with a single oscilloscope probe
connected across the input capacitor terminals.
Figure 15. Switching Waveforms for the Converter
in Figure 9 at Minimum VIN (8V)
VOUT
1V/DIV
IL
2A/DIV
MOSFET
DRAIN
VOLTAGE
20V/DIV
1μs/DIV
18717 F15
VIN = 8V
IOUT = 0.5A
VOUT = 42V
D = 81%
相关PDF资料 |
PDF描述 |
|---|---|
| LX1672-06CLQTR | 1 A DUAL SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LM3711XKMM-463/NOPB | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO10 |
| LMX2502LQX1635/NOPB | PLL FREQUENCY SYNTHESIZER, 19.68 MHz, QCC28 |
| LM385BDE4-1-2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8 |
| LM4040AIMX-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1871IMS-7-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Input Voltage,Current Mode Boost, Flyback and SEPIC Controller |
| LT1873-41 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT1873-41UR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT1880 | 制造商:LINER 制造商全称:Linear Technology 功能描述:SOT-23, Rail-to-Rail Output, Picoamp Input Current Precision Op Amp |
| LT1880CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP R-R O/P ±18V/36V 5-Pin TSOT-23 |
发布紧急采购，3分钟左右您将得到回复。