- 您现在的位置：买卖IC网 > PDF目录79915 > LT1871IMS-7#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LT1871IMS-7#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | PLASTIC, MSOP-10 |
| 文件页数： | 19/32页 |
| 文件大小： | 461K |
| 代理商： | LT1871IMS-7#TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC1871-7
26
18717fc
APPLICATIONS INFORMATION
rating for the inductor should be checked at the minimum
input voltage (which results in the highest inductor cur-
rent) and maximum output current.
SEPIC Converter: Power MOSFET Selection
Important parameters for the power MOSFET include the
drain-to-source breakdown voltage (BVDSS), the threshold
voltage (VGS(TH)), the on-resistance (RDS(ON)) versus gate-
to-source voltage, the gate-to-source and gate-to-drain
charges (QGS and QGD, respectively), the maximum drain
current (ID(MAX)) and the MOSFET’s thermal resistances
(RTH(JC) and RTH(JA)).
The gate drive voltage is set by the 7V INTVCC low dropout
regulator. Consequently, 6V rated threshold MOSFETs are
required in most LTC1871-7 applications.
The maximum voltage that the MOSFET switch must
sustain during the off-time in a SEPIC converter is equal
to the sum of the input and output voltages (VO + VIN).
As a result, careful attention must be paid to the BVDSS
specications for the MOSFETs relative to the maximum
actual switch voltage in the application. Many logic-level
devices are limited to 30V or less. Check the switching
waveforms directly across the drain and source terminals
of the power MOSFET to ensure the VDS remains below
the maximum rating for the device.
Sense Resistor Selection
During the MOSFET’s on-time, the control circuit limits
the maximum voltage drop across the power MOSFET to
about 150mV (at low duty cycle). The peak inductor cur-
rent is therefore limited to 150mV/RSENSE. The relationship
between the maximum load current, duty cycle and the
sense resistor is:
RSENSE
VSENSE(MAX)
IO(MAX)
1
1+
2
1
VO + VD
VIN(MIN)
+ 1
The VSENSE(MAX) term is typically 150mV at low duty
cycle and is reduced to about 100mV at a duty cycle of
92% due to slope compensation, as shown in Figure 11.
The constant ‘χ’ in the denominator represents the ripple
current in the inductors relative to their maximum cur-
rent. For example, if 30% ripple current is chosen, then
χ = 0.30.
Calculating Power MOSFET Switching and Conduction
Losses and Junction Temperatures
In order to calculate the junction temperature of the
power MOSFET, the power dissipated by the device must
be known. This power dissipation is a function of the
duty cycle, the load current and the junction temperature
itself. As a result, some iterative calculation is normally
required to determine a reasonably accurate value. Since
the controller is using the MOSFET as both a switching
and a sensing element, care should be taken to ensure
that the converter is capable of delivering the required
load current over all operating conditions (load, line and
temperature) and for the worst-case specications for
VSENSE(MAX) and the RDS(ON) of the MOSFET listed in the
manufacturer’s data sheet.
The power dissipated by the MOSFET in a SEPIC converter
is:
PFET = IO(MAX)
D
1–D
2
RDS(ON) D T
+ k VIN + VO
()2 IO(MAX) D
1–D
CRSS f
The rst term in the equation above represents the I2R
losses in the device and the second term, the switching
losses. The constant k = 1.7 is an empirical factor inversely
related to the gate drive current and has the dimension
of 1/current.
The ρT term accounts for the temperature coefcient of
the RDS(ON) of the MOSFET, which is typically 0.4%/°C.
Figure 12 illustrates the variation of normalized RDS(ON)
over temperature for a typical power MOSFET.
相关PDF资料 |
PDF描述 |
|---|---|
| LX1672-06CLQTR | 1 A DUAL SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LM3711XKMM-463/NOPB | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO10 |
| LMX2502LQX1635/NOPB | PLL FREQUENCY SYNTHESIZER, 19.68 MHz, QCC28 |
| LM385BDE4-1-2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8 |
| LM4040AIMX-2.5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1871IMS-7-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Input Voltage,Current Mode Boost, Flyback and SEPIC Controller |
| LT1873-41 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT1873-41UR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic |
| LT1880 | 制造商:LINER 制造商全称:Linear Technology 功能描述:SOT-23, Rail-to-Rail Output, Picoamp Input Current Precision Op Amp |
| LT1880CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP R-R O/P ±18V/36V 5-Pin TSOT-23 |
发布紧急采购，3分钟左右您将得到回复。