参数资料
型号: LT1871IMS-7#TR
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10
封装: PLASTIC, MSOP-10
文件页数: 8/32页
文件大小: 461K
代理商: LT1871IMS-7#TR
LTC1871-7
16
18717fc
APPLICATIONS INFORMATION
From a known power dissipated in the power MOSFET, its
junction temperature can be obtained using the following
formula:
TJ = TA + PFET RTH(JA)
The RTH(JA) to be used in this equation normally includes
the RTH(JC) for the device plus the thermal resistance from
the case to the ambient temperature (RTH(CA)). This value
of TJ can then be compared to the original, assumed value
used in the iterative calculation process.
Boost Converter: Output Diode Selection
To maximize efciency, a fast switching diode with low
forward drop and low reverse leakage is desired. The output
diode in a boost converter conducts current during the
switch off-time. The peak reverse voltage that the diode
must withstand is equal to the regulator output voltage.
The average forward current in normal operation is equal
to the output current, and the peak current is equal to the
peak inductor current.
ID(PEAK) =IL(PEAK) = 1+ 2
IO(MAX)
1–DMAX
The power dissipated by the diode is:
PD = IO(MAX) VD
and the diode junction temperature is:
TJ = TA + PD RTH(JA)
Figure 12. Normalized RDS(ON) vs Temperature
JUNCTION TEMPERATURE (°C)
–50
ρ
TNORMALIZED
ON
RESISTANCE
1.0
1.5
150
18717 F12
0.5
0
50
100
2.0
The RTH(JA) to be used in this equation normally includes
the RTH(JC) for the device plus the thermal resistance from
the board to the ambient temperature in the enclosure.
Remember to keep the diode lead lengths short and to
observe proper switch-node layout (see Board Layout
Checklist) to avoid excessive ringing and increased dis-
sipation.
Boost Converter: Output Capacitor Selection
Contributions of ESR (equivalent series resistance), ESL
(equivalent series inductance) and the bulk capacitance
must be considered when choosing the correct component
for a given output ripple voltage. The effects of these three
parameters (ESR, ESL and bulk C) on the output voltage
ripple waveform are illustrated in Figure 13 for a typical
boost converter.
The choice of component(s) begins with the maximum
acceptable ripple voltage (expressed as a percentage of
the output voltage), and how this ripple should be divided
between the ESR step and the charging/discharging ΔV.
For the purpose of simplicity we will choose 2% for the
maximum output ripple, to be divided equally between the
ESR step and the charging/discharging ΔV. This percentage
ripple will change, depending on the requirements of the
application, and the equations provided below can easily
be modied.
For a 1% contribution to the total ripple voltage, the ESR
of the output capacitor can be determined using the fol-
lowing equation:
ESRCOUT
0.01 VO
IIN(PEAK)
where:
IIN(PEAK)= 1+ 2
IO(MAX)
1–DMAX
For the bulk C component, which also contributes 1% to
the total ripple:
COUT
IO(MAX)
0.01 VO f
相关PDF资料
PDF描述
LX1672-06CLQTR 1 A DUAL SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38
LM3711XKMM-463/NOPB 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO10
LMX2502LQX1635/NOPB PLL FREQUENCY SYNTHESIZER, 19.68 MHz, QCC28
LM385BDE4-1-2 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8
LM4040AIMX-2.5 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8
相关代理商/技术参数
参数描述
LT1871IMS-7-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:High Input Voltage,Current Mode Boost, Flyback and SEPIC Controller
LT1873-41 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic
LT1873-41UR 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic
LT1880 制造商:LINER 制造商全称:Linear Technology 功能描述:SOT-23, Rail-to-Rail Output, Picoamp Input Current Precision Op Amp
LT1880CS5 制造商:Linear Technology 功能描述:OP Amp Single GP R-R O/P ±18V/36V 5-Pin TSOT-23