参数资料
| 型号： | LT1913IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 3.5A 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.79 V ~ 25 V |
| 输入电压： | 3.6 V ~ 25 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 2.4MHz |
| 电流 - 输出： | 3.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LT1913
APPLICATIONS INFORMATION
R1 = R2
V OUT
FB Resistor Network
The output voltage is programmed with a resistor divider
between the output and the FB pin. Choose the 1% resis-
tors according to:
–1
0.79V
Reference designators refer to the Block Diagram.
Setting the Switching Frequency
The LT1913 uses a constant frequency PWM architecture
that can be programmed to switch from 200kHz to 2.4MHz
by using a resistor tied from the RT pin to ground. A table
showing the necessary RT value for a desired switching
frequency is in Figure 1.
where V IN is the typical input voltage, V OUT is the output
voltage, V D is the catch diode drop (~0.5V) and V SW is the
internal switch drop (~0.5V at max load). This equation
shows that slower switching frequency is necessary to
safely accommodate high V IN /V OUT ratio. Also, as shown
in the next section, lower frequency allows a lower dropout
voltage. The reason input voltage range depends on the
switching frequency is because the LT1913 switch has ?nite
minimum on and off times. The switch can turn on for a
minimum of ~150ns and turn off for a minimum of ~150ns.
Typical minimum on time at 25°C is 80ns. This means that
the minimum and maximum duty cycles are:
DC MIN = f SW t ON ( MIN )
DC MAX = 1– f SW t OFF ( MIN )
SWITCHING FREQUENCY (MHz)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
R T VALUE (k Ω )
215
140
100
78.7
63.4
53.6
45.3
39.2
34
26.7
22.1
18.2
15
12.7
10.7
9.09
where f SW is the switching frequency, the t ON(MIN) is the
minimum switch on time (~150ns), and the t OFF(MIN) is
the minimum switch off time (~150ns). These equations
show that duty cycle range increases when switching
frequency is decreased.
A good choice of switching frequency should allow ad-
equate input voltage range (see next section) and keep
the inductor and capacitor values small.
Input Voltage Range
The maximum input voltage for LT1913 applications
depends on switching frequency and Absolute Maxi-
mum Ratings of the V IN and BOOST pins (25V and 50V
Figure 1. Switching Frequency vs. R T Value
Operating Frequency Tradeoffs
Selection of the operating frequency is a tradeoff between
respectively).
While the output is in start-up, short-circuit, or other
overload conditions, the switching frequency should be
chosen according to the following equation:
ef?ciency, component size, minimum dropout voltage, and
maximum input voltage. The advantage of high frequency
operation is that smaller inductor and capacitor values may
V IN ( MAX ) =
V OUT + V D
f SW t ON ( MIN )
– V D + V SW
f SW ( MAX ) =
be used. The disadvantages are lower ef?ciency, lower
maximum input voltage, and higher dropout voltage. The
highest acceptable switching frequency (f SW(MAX) ) for a
given application can be calculated as follows:
V D + V OUT
t ON ( MIN ) ( V D + V IN – V SW )
where V IN(MAX) is the maximum operating input voltage,
V OUT is the output voltage, V D is the catch diode drop
(~0.5V), V SW is the internal switch drop (~0.5V at max
load), f SW is the switching frequency (set by R T ), and
t ON(MIN) is the minimum switch on time (~100ns). Note that
a higher switching frequency will depress the maximum
1913f
10
相关PDF资料 |
PDF描述 |
|---|---|
| LT1930AES5#TRM | IC REG BOOST ADJ 1A TSOT23-5 |
| LT1931AIS5#TRPBF | IC REG INV 1A TSOT23-5 |
| LT1933HS6#TRMPBF | IC REG BUCK ADJ 0.6A TSOT23-6 |
| LT1934IDCB-1#TRPBF | IC REG BUCK ADJ 60MA 6DFN |
| LT1935ES5#TRM | IC REG BST FLYBK SEPIC TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1920 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Resistor Gain Programmable, Precision Instrumentation Amplifier |
| LT1920C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single Resistor Gain Programmable, Precision Instrumentation Amplifier |
| LT1920CN8 | 功能描述:IC PREC INSTRUMENTATION AMP 8DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:350 V/µs 增益带宽积:180MHz -3db带宽:320MHz 电流 - 输入偏压:12.5µA 电压 - 输入偏移:800µV 电流 - 电源:15mA 电流 - 输出 / 通道:85mA 电压 - 电源，单路/双路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| LT1920CN8#PBF | 功能描述:IC PREC INSTRUMENTATION AMP 8DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:350 V/µs 增益带宽积:180MHz -3db带宽:320MHz 电流 - 输入偏压:12.5µA 电压 - 输入偏移:800µV 电流 - 电源:15mA 电流 - 输出 / 通道:85mA 电压 - 电源，单路/双路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
| LT1920CS8 | 功能描述:IC PREC INSTRUMNTATION AMP 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:350 V/µs 增益带宽积:180MHz -3db带宽:320MHz 电流 - 输入偏压:12.5µA 电压 - 输入偏移:800µV 电流 - 电源:15mA 电流 - 输出 / 通道:85mA 电压 - 电源，单路/双路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。