- 您现在的位置：买卖IC网 > PDF目录30766 > LT1952MPGN#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LT1952MPGN#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 5/28页 |
| 文件大小： | 357K |
| 代理商： | LT1952MPGN#PBF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1952/LT1952-1
13
19521fe
Shutdown and Programming Undervoltage Lockout
The LT1952/LT1952-1 have an accurate 1.32V shutdown
threshold at the SD_VSEC pin. This threshold can be
used in conjunction with a resistor divider to define the
undervoltage lockout threshold (UVLO) of the system
input voltage (VS) to the power converter (Figure 3). A pin
current hysteresis (10A before part turn on, 0A after
part turn on) allows UVLO hysteresis to be programmed.
Calculation of the ON/OFF thresholds for the supply (SVIN)
to the power converter can be made as follows:
VS OFF Threshold = 1.32[1 + (R1/R2)]
VS ON Threshold = SVINOFF+(10AR1)
A simple open drain transistor can be added to the resistor
divider network at the SD_VSEC pin to control the turn off
of the LT1952/LT1952-1 (Figure 3).
The SD_VSEC pin must not be left open since there must
be an external source current >10A to lift the pin past its
1.32V threshold for part turn on.
APPLICATIONS INFORMATION
Micropower Start-Up: Selection of Start-Up Resistor
and Capacitor for VIN
The LT1952/LT1952-1 use turn-on voltage hysteresis at
the VIN pin and low start-up current to allow micro-power
start-up (Figure 4). The LT1952/LT1952-1 monitor VIN pin
voltage to allow part turn on at 14.25V (7.75V LT1952-1)
and part turn off at 8.75V (6.5V LT1952-1). Low start-up
OPERATION
Slope Compensation
The current mode architecture requires slope compensa-
tion to be added to the current sensing loop to prevent
subharmonic oscillations which can occur for duty cycles
above 50%. Unlike most current mode converters which
have a slope compensation ramp that is fixed internally,
placing a constraint on inductor value and operating
frequency, the LT1952/LT1952-1 have externally adjust-
able slope compensation. Slope compensation can be
programmed by inserting an external resistor (RSLOPE)
in series with the ISENSE pin. The LT1952/LT1952-1 have
a linear slope compensation ramp which sources current
out of the ISENSE pin of approximately 8A at 0% duty
cycle to 35A at 80% duty cycle.
Overcurrent Detection and Soft-Start (OC Pin)
An added feature to the LT1952/LT1952-1 is a precise
100mV sense threshold at the OC pin used to detect
overcurrent conditions in the converter and set a soft-start
latch. The OC pin is connected directly to the source of
the primary side MOSFET to monitor peak current in the
MOSFET (Figure 7). The 107mV threshold is constant
over the entire duty cycle range of the converter because
it is unaffected by the slope compensation added to the
ISENSE pin.
Synchronizing
A SYNC pin allows the LT1952/LT1952-1 oscillator to be
synchronized to an external clock. The SYNC pin can be
driven from a logic level output, requiring less than 0.8V
for a logic level low and greater than 2.2V for a logic level
high. Duty cycle should run between 10% and 90%. To
avoid loss of slope compensation during synchroniza-
tion, the free running oscillator frequency (fOSC) should
be programmed to 80% of the external clock frequency
(fSYNC).TheRSLOPEresistorchosenfornon-synchronized
operation should be increased by 1.25x (= fSYNC/fOSC).
Figure 3. Programming Undervoltage Lockout (UVLO)
1.32V
SYSTEM
INPUT (VS)
OPTIONAL
SHUTDOWN
TRANSISTOR
1952 F03
SD_VSEC
11A
LT1952/LT1952-1
R1
R2
+
–
OFF
ON
相关PDF资料 |
PDF描述 |
|---|---|
| LT1952MPGN-1#TRPBF | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT1952MPGN#TRPBF | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3412AIFE | 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3412AEFE#TRPBF | 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3412AEUF#TRPBF | 3 A SWITCHING REGULATOR, 4 kHz SWITCHING FREQ-MAX, PQCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1956 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:100V Synchronous Switching Regulator Controller |
| LT1956-5 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, 1.5A, 500kHz Step-Down Switching Regulators |
| LT1956EFE | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956EFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1956EFE#TR | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。