- 您现在的位置：买卖IC网 > PDF目录13881 > LT1956IFE-5#PBF (Linear Technology)IC REG BUCK 5V 1.5A 16TSSOP PDF资料下载
参数资料
| 型号： | LT1956IFE-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 5V 1.5A 16TSSOP |
| 标准包装： | 95 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 5V |
| 输入电压： | 5.5 V ~ 60 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-TSSOP-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT1956/LT1956-5
APPLICATIO S I FOR ATIO
Output capacitor ripple current (RMS):
is to prevent excessive ripple causing dips below the mini-
I RIPPLE ( RMS ) =
0 .29 ( V OUT )( V IN – V OUT )
( L )( f )( V IN )
mum operating voltage resulting in erratic operation.
Depending on how the LT1956 circuit is powered up you
may need to check for input voltage transients.
Ceramic Capacitors
Ceramic capacitors are generally chosen for their good
high frequency operation, small size and very low ESR
(effective series resistance). Their low ESR reduces
output ripple voltage but also removes a useful zero in the
loop frequency response, common to tantalum capaci-
tors. To compensate for this, a resistor R C can be placed
in series with the V C compensation capacitor C C . Care
must be taken however, since this resistor sets the high
frequency gain of the error amplifier, including the gain
at the switching frequency. If the gain of the error
amplifier is high enough at the switching frequency,
output ripple voltage (although smaller for a ceramic
output capacitor) may still affect the proper operation of
the regulator. A filter capacitor C F in parallel with the
R C /C C network is suggested to control possible ripple at
the V C pin. The LT1956 can be stabilized for V OUT = 5V at
1A using a 22 μ F ceramic output capacitor and V C com-
ponent values of C C = 4700pF, R C = 4.7k and C F = 220pF.
INPUT CAPACITOR
Step-down regulators draw current from the input supply
in pulses. The rise and fall times of these pulses are very
fast. The input capacitor is required to reduce the voltage
ripple this causes at the input of LT1956 and force the
switching current into a tight local loop, thereby minimiz-
ing EMI. The RMS ripple current can be calculated from:
The input voltage transients may be caused by input
voltage steps or by connecting the LT1956 converter to an
already powered up source such as a wall adapter. The
sudden application of input voltage will cause a large
surge of current in the input leads that will store energy in
the parasitic inductance of the leads. This energy will
cause the input voltage to swing above the DC level of input
power source and it may exceed the maximum voltage
rating of input capacitor and LT1956.
The easiest way to suppress input voltage transients is to
add a small aluminum electrolytic capacitor in parallel with
the low ESR input capacitor. The selected capacitor needs
to have the right amount of ESR in order to critically
dampen the resonant circuit formed by the input lead
inductance and the input capacitor. The typical values of
ESR will fall in the range of 0.5 ? to 2 ? and capacitance will
fall in the range of 5 μ F to 50 μ F.
If tantalum capacitors are used, values in the 22 μ F to
470 μ F range are generally needed to minimize ESR and
meet ripple current and surge ratings. Care should be
taken to ensure the ripple and surge ratings are not
exceeded. The AVX TPS and Kemet T495 series are surge
rated. AVX recommends derating capacitor operating
voltage by 2 for high surge applications.
CATCH DIODE
Highest efficiency operation requires the use of a Schottky
I RIPPLE ( RMS ) C IN = I OUT
V OUT ( V IN – V OUT )
V IN 2
type diode. DC switching losses are minimized due to its
low forward voltage drop, and AC behavior is benign due
to its lack of a significant reverse recovery time. Schottky
diodes are generally available with reverse voltage ratings
Ceramic capacitors are ideal for input bypassing. At 500kHz
switching frequency, the energy storage requirement of
the input capacitor suggests that values in the range of
2.2 μ F to 10 μ F are suitable for most applications. If opera-
tion is required close to the minimum input required by the
output of the LT1956, a larger value may be required. This
of up to 60V and even 100V, and are price competitive with
other types.
The use of so-called “ultrafast” recovery diodes is gener-
ally not recommended. When operating in continuous
mode, the reverse recovery time exhibited by “ultrafast”
diodes will result in a slingshot type effect. The power
1956f
14
相关PDF资料 |
PDF描述 |
|---|---|
| UWT0G330MCR1GB | CAP ALUM 33UF 4V 20% SMD |
| GCM36DTAT | CONN EDGECARD 72POS R/A .156 SLD |
| LT1766IFE-5#PBF | IC REG BUCK 5V 1.5A 16TSSOP |
| UWT0G220MCR1GB | CAP ALUM 22UF 4V 20% SMD |
| 25ZL100MEFCTA8X7 | CAP ALUM 100UF 25V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1956IGN | 功能描述:IC REG BUCK ADJ 1.5A 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956IGN#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1956IGN#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR SSOP-16 |
| LT1956IGN#TR | 功能描述:IC REG BUCK ADJ 1.5A 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1956IGN#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。