参数资料
| 型号： | LT1994MPDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/DRIVER LN 8-MSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 65 V/µs |
| 增益带宽积： | 70MHz |
| 电流 - 输入偏压： | 18µA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 14.8mA |
| 电流 - 输出 / 通道： | 85mA |
| 电压 - 电源，单路/双路(±)： | 2.375 V ~ 12.6 V，±1.188 V ~ 6.3 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LT1994
12
1994fb
VICM is dened as the average of the two input voltages,
VINP and VINM (also called the input common mode
voltage):
VV
V
ICM
INP
INM
=+
()
1
2
and VINDIFF is dened as the difference of the input
voltages:
VINDIFF = VINP – VINM
When the feedback ratios mismatch (
Δβ), common mode
to differential conversion occurs.
Setting the differential input to zero (VINDIFF = 0), the de-
gree of common mode to differential conversion is given
by the equation:
VV
V
VV
V
OUTDIFF
OUT
ICM
OCM
AVG
INDIFF
–
0
In general, the degree of feedback pair mismatch is a source
of common mode to differential conversion of both signals
and noise. Using 1% resistors or better will provide about
28dB of common mode rejection. Using 0.1% resistors
will provide about 48dB of common mode rejection. A low
impedance ground plane should be used as a reference
for both the input signal source and the VOCM pin. A direct
short of VOCM to this ground plane or bypassing the VOCM
with a high quality 0.1μF ceramic capacitor to this ground
plane will further mitigate against common mode signals
from being converted to differential.
Input Impedance and Loading Effects
The input impedance looking into the VINP or VINM input
of Figure 1 depends on whether or not the sources VINP
and VINM are fully differential. For balanced input sources
(VINP = –VINM), the input impedance seen at either input
is simply:
RINP = RINM = RI
For single-ended inputs, because of the signal imbalance
at the input, the input impedance actually increases over
the balanced differential case. The input impedance looking
into either input is:
RR
R
RR
INP
INM
I
F
IF
==
+
1
2
–
Input signal sources with non-zero output impedances can
also cause feedback imbalance between the pair of feedback
networks. For the best performance, it is recommended
that the source’s output impedance be compensated for.
If input impedance matching is required by the source,
R1 should be chosen (see Figure 3):
R
RR
INM
S
INM
S
1
=
According to Figure 3, the input impedance looking into
the differential amp (RINM)reectsthesingle-endedsource
case, thus:
R
RR
INM
I
F
IF
=
+
1
2
–
R2 is chosen to balance R1||RS:
R
RR
S
2
1
=
+
Figure 3. Optimal Compensation for Signal-Source Impedance
1994 F03
RI
RF
RS
VS
+
–
+
LT1994
RI
RF
R2 = RS || R1
R1 CHOSEN SO THAT R1 || RINM = RS
R2 CHOSEN TO BALANCE R1 || RS
R1
RINM
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LT1999MPS8-50#PBF | IC AMP CURR SENSE HV 8-MSOP |
| LT2079AIS#TRPBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| LT2178CS8 | IC OPAMP MICROPOWER DUAL 8-SOIC |
| LT318AN8#PBF | IC OPAMP HI-SPEED 15MHZ 8-DIP |
| LT6002IGN#PBF | IC OP AMP R-R 1.8V QUAD 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1995 | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD#PBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| LT1995CDD#TRPBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT1995CMS | 功能描述:IC AMP GAIN SELECT 10MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。