参数资料
| 型号： | LT1994MPDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/DRIVER LN 8-MSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 65 V/µs |
| 增益带宽积： | 70MHz |
| 电流 - 输入偏压： | 18µA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 14.8mA |
| 电流 - 输出 / 通道： | 85mA |
| 电压 - 电源，单路/双路(±)： | 2.375 V ~ 12.6 V，±1.188 V ~ 6.3 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
15
1994fb
LT1994
In general, the die temperature can be estimated from
the ambient temperature TA, and the device power dis-
sipation PD:
TJ = TA+ + PD θJA
The power dissipation in the IC is a function of the supply
voltage, the output voltage, and the load resistance. For
fully differential output ampliers at a given supply voltage
(±VCC), and a given differential load (RLOAD), the worst-
case power dissipation PD(MAX) occurs at the worst-case
quiescent current (IQ(MAX) = 20.5mA) and when the load
current is given by the expression:
I
V
R
LOAD
CC
LOAD
=
The worst-case power dissipation in the LT1994 at
I
V
R
LOAD
CC
LOAD
=
is:
PV
I
R
V
R
VI
DMAX
CC
LOAD
Q MAX
LOAD
CC
LOAD
CC
QMAX
()
=+
()
=+
2
–
Example: A LT1994 is mounted on a circuit board in a
MSOP-8 package (
θJA = 140°C/W), and is running off of
±5V supplies driving an equivalent load (external load plus
feedback network) of 75
Ω. The worst-case power that
would be dissipated in the device occurs when:
P
V
R
VI
V
DMAX
CC
LOAD
CC
QMAX
()
=+
2
5
75
25
Ω
.
17 5
0 54
MA
W
=
The maximum ambient temperature the 8-lead MSOP is
allowed to operate under these conditions is:
TA = TJMAX – PD θJA = 150°C – (0.54W)
(140°C/W) = 75°C
To operate the device at higher ambient temperature,
connect more copper to the V– pin to reduce the thermal
resistance of the package as indicated in Table 1.
Table 1. LT1994 MSOP Package Thermal Resistivity
COPPER AREA
TOPSIDE (mm2)
COPPER AREA
BACKSIDE (mm2)
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
00
140
30
0
135
100
0
130
100
120
540
110
Layout Considerations
Because the LT1994 is a high speed amplier, it is sensitive
to both stray capacitance and stray inductance. Compo-
nents connected to the LT1994 should be connected with
as short and direct connections as possible. A low noise,
low impedance ground plane is critical for the highest
performance. In single-supply applications, high quality
surface mount 1μF and 0.1μF ceramic bypass capacitors
with minimum PCB trace should be used directly across
the power supplies V+ to V–. In split supply applications,
high quality surface mount 1μF and 0.1μF ceramic bypass
capacitors should be placed across the power supplies
V+ to V–, and individual high quality surface mount 0.1μF
bypass capacitors should be used from each supply to
ground with direct (short) connections.
Any stray parasitic capacitance to ground at the summing
junctions, IN+ and IN– should be kept to an absolute mini-
mum even if it means stripping back the ground plane
away from any trace attached to this node. This becomes
especially true when the feedback resistor network uses
resistor values >500
Ω in circuits with RF = RI. Excessive
peaking in the frequency response can be mitigated by
adding small amounts of feedback capacitance around RF
(2pF to 5pF). Always keep in mind the differential nature of
the LT1994, and that it is critical that the output impedances
seen by both outputs (stray or intended) should be as bal-
anced and symmetric as possible. This will help preserve
the natural balance of the LT1994, which minimizes the
generation of even order harmonics, and preserves the
rejection of common mode signals and noise.
It is highly recommended that the VOCM pin be either hard
tied to a low impedance ground plane (in split supply
applications) or bypassed to ground with a high quality
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LT1999MPS8-50#PBF | IC AMP CURR SENSE HV 8-MSOP |
| LT2079AIS#TRPBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| LT2178CS8 | IC OPAMP MICROPOWER DUAL 8-SOIC |
| LT318AN8#PBF | IC OPAMP HI-SPEED 15MHZ 8-DIP |
| LT6002IGN#PBF | IC OP AMP R-R 1.8V QUAD 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1995 | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD#PBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| LT1995CDD#TRPBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT1995CMS | 功能描述:IC AMP GAIN SELECT 10MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。