参数资料
| 型号： | LT1994MPDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/DRIVER LN 8-MSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 65 V/µs |
| 增益带宽积： | 70MHz |
| 电流 - 输入偏压： | 18µA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 14.8mA |
| 电流 - 输出 / 通道： | 85mA |
| 电压 - 电源，单路/双路(±)： | 2.375 V ~ 12.6 V，±1.188 V ~ 6.3 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LT1994
14
1994fb
A plot of this equation and a plot of the noise generated
by the feedback components are shown in Figure 6.
The LT1994’s input referred voltage noise contributes the
equivalent noise of a 560
Ω resistor. When the feedback
network is comprised of resistors whose values are less
than this, the LT1994’s output noise is voltage noise
dominant (See Figure 6):
ee
R
no
ni
F
I
≈+
1
Feedback networks consisting of resistors with values
greater than about 10k will result in output noise which
is amplier current noise dominant.
eI
R
no
n
F
≈ 2
Lower resistor values always result in lower noise at the
penalty of increased distortion due to increased loading of
the feedback network on the output. Higher resistor values
will result in higher output noise, but improved distortion
due to less loading on the output.
Figure 6 shows the noise voltage that will appear differ-
entially between the outputs. The common mode output
noise voltage does not add to this differential noise. For
optimum noise and distortion performance, use a dif-
ferential output conguration.
Power Dissipation Considerations
The LT1994 is housed in either an 8-lead MSOP package
(
θJA = 140°C/W or an 8-lead DD package (θJA = 43°C/W).
The LT1994 combines high speed and large output current
with a small die and small package so there is a need to
be sure the die temperature does not exceed 150°C. In the
8-lead MSOP, LT1994 has its V– lead fused to the frame
so it is possible to lower the package thermal impedance
by connecting the V– pin to a large ground plane or metal
trace. Metal trace and plated through holes can be used to
spread the heat generated by the device to the backside
of the PC board. For example, an 8-lead MSOP on a 3/32"
FR-4 board with 540mm2 of 2oz. copper on both sides
of the PC board tied to the V– pin can drop the
θJA from
140°C/W to 110°C/W (see Table 1).
The underside of the DD package has exposed metal
(4mm2) from the lead frame where the die is attached.
This provides for the direct transfer of heat from the die
junction to the printed circuit board to help control the
maximum operating junction temperature. The dual-in-line
pin arrangement allows for extended metal beyond the
ends of the package on the topside (component side) of a
circuit board. Table 1 summarizes for the MSOP package,
the thermal resistance from the die junction-to-ambient
that can be obtained using various amounts of topside,
and backside metal (2oz. copper). On multilayer boards,
further reductions can be obtained using additional metal
on inner PCB layers connected through vias beneath the
package.
Figure 6. LT1994 Output Spot Noise vs Spot Noise Contributed by
Feedback Network Alone
RF = RI (kΩ)
0.1
1
OUTPUT
NOISE
(nV/√Hz)
10
100
110
1994 F06
TOTAL
(AMPLIFIER + FEEDBACK NETWORK)
OUTPUT NOISE
FEEDBACK NETWORK
NOISE ALONE
1994 F05
RI2
RF2
VS/2
–VS/2
+
–
+
3
7
6
8
1
2
5
4
LT1994
VOCM
enRI2
2
RI1
RF1
encm
2
eno
2
in–
2
enRI1
2
eni
2
enRF2
2
enRF1
2
in+
2
Figure 5. Noise Analysis
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LT1999MPS8-50#PBF | IC AMP CURR SENSE HV 8-MSOP |
| LT2079AIS#TRPBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| LT2178CS8 | IC OPAMP MICROPOWER DUAL 8-SOIC |
| LT318AN8#PBF | IC OPAMP HI-SPEED 15MHZ 8-DIP |
| LT6002IGN#PBF | IC OP AMP R-R 1.8V QUAD 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1995 | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:32MHz, 1000V/μs Gain Selectable Amplifier |
| LT1995CDD#PBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
| LT1995CDD#TRPBF | 功能描述:IC AMP GAIN SELECT 10-DFN RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:0.11 V/µs 增益带宽积:350kHz -3db带宽:- 电流 - 输入偏压:4nA 电压 - 输入偏移:20µV 电流 - 电源:260µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SO 包装:带卷 (TR) |
| LT1995CMS | 功能描述:IC AMP GAIN SELECT 10MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。