参数资料
| 型号： | LT3032IDE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .15A 14DFN |
| 产品培训模块： | LT3032 - 150mA Dual Positive/Negative Low Noise LDO |
| 特色产品： | LT3032 Voltage Linear Regulator |
| 标准包装： | 91 |
| 稳压器拓扑结构： | 正可调式和负可调式 |
| 输出电压： | ±1.22 V ~ ±20 V |
| 输入电压： | ±2.3 V ~ ±20 V |
| 电压 - 压降（标准）： | 0.27V @ 150mA，0.3V @ -150mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 170mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-DFN（4x3） |
| 包装： | 管件 |
| 产品目录页面： | 1330 (CN2011-ZH PDF) |
LT3032 Series
PIN FUNCTIONS
OUTP (Pin 1): Positive Output. This output supplies power
to the positive side load. A minimum output capacitor
of 2.2μF is required to prevent oscillations. Larger out-
put capacitors are required for applications with large
transient loads to limit peak voltage transients. See the
Applications Information section for more information
on output capacitance, bypass capacitance, and reverse
output characteristics.
ADJP (Pin 2, Adjustable Part Only): Positive Adjust. This
is the input to the positive side error ampli?er. This pin
is internally clamped to ±7V. It has a typical bias current
of 30nA which ?ows into the pin (see curve of ADJP Pin
Bias Current vs Temperature in the Typical Performance
Characteristics). The ADJP pin voltage is 1.22V referenced
to ground and the output voltage range is 1.22V to 20V.
BYPP (Pin 3): Positive Bypass. The BYPP pin is used to
bypass the reference of the positive side regulator to achieve
low noise performance. The BYPP pin is clamped internally
to ±0.6V (one V BE ). A small capacitor from OUTP to this pin
will bypass the reference to lower the output voltage noise.
A maximum value of 0.01μF is used for reducing output
voltage noise to a typical 20μV RMS over the 10Hz to 100kHz
bandwidth. If not used, this pin must be left unconnected.
GND (Pins 4, 5, Exposed Pad Pin 15): Ground. One of
the DFN’s exposed backside pads (Pin 15) is an electrical
connection to ground. To ensure proper electrical and
thermal performance, solder Pin 15 to the PCB’s ground
and tie directly to Pins 4 and 5. Connect the bottom of
the positive and negative output voltage setting resistor
dividers directly to Pins 4 and 5 for optimum load regula-
tion performance.
INN (Pin 6, 9, Exposed Pad Pin 16): Negative Input. The
DFN package’s second exposed backside pad (Pin 16) is
an electrical connection to INN. To ensure proper electri-
cal and thermal performance, solder Pin 16 to the PCB’s
negative input supply and tie directly to Pins 6 and 9.
Power is supplied to the negative side of the LT3032
through the INN pins. A bypass capacitor is required on
this pin if it is more than six inches away from the main
input ?lter capacitor. In general, the output impedance of
a battery rises with frequency, so it is advisable to include
a bypass capacitor in battery-powered circuits. A bypass
capacitor in the range of 1μF to 10μF is suf?cient.
OUTN (Pin 7): Negative Output. This output supplies power
to the negative side load. A minimum output capacitor
of 1μF is required to prevent oscillations. Larger output
capacitors are required for applications with large tran-
sient loads to limit peak voltage transients. A parasitic
diode exists between OUTN and INN; OUTN can not be
pulled more negative than INN during normal operation,
or more than 0.5V below INN during a fault condition. See
the Applications Information section for more information
on output capacitance and bypass capacitors.
ADJN (Pin 8, Adjustable Part Only): Negative Adjust. This
is the input to the negative side error ampli?er. The ADJN
pin has a typical bias current of 30nA that ?ows out of the
pin. The ADJN pin voltage is –1.22V referenced to ground,
and the output voltage range is –1.22V to –20V. A parasitic
diode exists between ADJN and INN. The ADJN pin cannot
be pulled more negative than INN during normal operation,
or more than 0.5V below INN during a fault condition.
SHDNN (Pin 10): Negative Shutdown. The SHDNN pin puts
the negative side into a low power shutdown state. The
SHDNN pin is referenced to ground for regulator control,
allowing the negative side to be driven by either positive
or negative logic. The negative output will be off if the
SHDNN pin is within ±0.8V(typical) of ground. Pulling the
SHDNN pin more than –1.9V or +1.4V(typical) will turn the
negative output on. The SHDNN pin can be driven by 5V
logic or open-collector logic with a pull-up resistor. The
pull-up resistor is required to supply the pull-up current of
the open-collector device, normally several microamperes,
and the SHDNN pin current, typically 3μA out of the pin
(for negative logic) or 6μA into the pin (for positive logic).
If unused, the SHDNN pin must be connected to INN. The
negative output will be shut down if the SHDNN pin is open
circuit. A parasitic diode exists between SHDNN and INN,
the SHDNN pin cannot be pulled more negative than INN
during normal operation, or more than 0.5V below INN
during a fault condition.
3032fd
14
相关PDF资料 |
PDF描述 |
|---|---|
| RSM36DTBD-S664 | CONN EDGECARD 72POS R/A .156 |
| LFECP6E-3FN484I | IC FPGA 6.1KLUTS 484FPBGA |
| LFEC6E-3T144I | IC FPGA 6.1KLUTS 97I/O 144-TQFP |
| MAX4945LELA+T | IC CTLR OVP W/FET 5.80V 8UDFN |
| MAX4945AELA+T | IC CTLR OVP W/FET 5.80V 8UDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3032IDETR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 150mA Positive/Negative Low Noise Low Dropout Linear Regulator |
| LT3032IDETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 150mA Positive/Negative Low Noise Low Dropout Linear Regulator |
| LT3032MPDE#PBF | 功能描述:IC REG LDO ADJ .15A 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT3032MPDE#TRPBF | 功能描述:IC REG LDO ADJ .15A 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT3032MPDE-12#PBF | 功能描述:IC REG LDO +-12V .15A 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。