- 您现在的位置：买卖IC网 > PDF目录79982 > LT3579EFE-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PDSO20 PDF资料下载
参数资料
| 型号： | LT3579EFE-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO20 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件页数： | 38/40页 |
| 文件大小： | 503K |
| 代理商： | LT3579EFE-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页
LT3579/LT3579-1
7
35791f
pin FuncTions
GATE (Pin 1/Pin 3): PMOS Gate Drive Pin. The GATE pin
is a pull-down current source, and can be used to drive
the gate of an external PMOS transistor for output short
circuit protection or output disconnect. The GATE pin
current increases linearly with the SS pin’s voltage, with
a maximum pull-down current of 933A at SS voltages
exceeding 500mV. Note that if the SS voltage is greater
than 500mV, and the GATE pin voltage is less than 2V, the
GATE pin looks like a 2k impedance to ground. See the
Appendix for more information.
FAULT (Pin 2/Pin 4): Fault Indication Pin. This active
low, bidirectional pin can either be pulled low (below
750mV) by an external source, or internally by the chip
to indicate a fault. When pulled low, this pin causes the
power switches to turn off, the GATE pin to become high
impedance, the CLKOUT pin to become disabled, and the
SS pin to go through a charge/discharge sequence. The
end/absence of a fault is indicated when the voltage on this
pin exceeds 1V. A pull-up resistor or some other form of
pull-up network needs to exist on this pin to pull it above
1V in the absence of a fault.
VIN (Pin 3/Pin 5): Input Supply Pin. Must be locally
bypassed.
SW1 (Pins 4 - 7/Pins 6 - 10): Master Switch Pin. This is the
collector of the internal master NPN power switch. SW1
is designed to handle a peak collector current of 3.4A
(minimum). Minimize the metal trace area connected to
this pin to minimize EMI.
GND(Pins8,9,ExposedPadPin21/ExposedPadPin21):
Ground. Must be soldered directly to local ground
plane.
SW2 (Pins 10-13/Pins 11-15): Slave Switch Pin. This is
the collector of the internal slave NPN power switch. SW2
is designed to handle a peak collector current of 2.6A
(minimum). Minimize the metal trace area connected to
this pin to minimize EMI.
CLKOUT (Pin 14/Pin 16): Clock Output Pin. Use this pin to
synchronize one or more other ICs to the LT3579. This pin
oscillatesatthesamefrequencyastheinternaloscillatorof
the part or as the SYNC pin. CLKOUT may also be used as
a temperature monitor since the CLKOUT pin’s duty cycle
varies linearly with the part’s junction temperature. The
CLKOUT pin signal of the LT3579-1 is 180° out of phase
with the internal oscillator or SYNC pin, and the duty cycle
is fixed at ~50%. The LT3579-1 is useful for multiphase
switching regulators.
SHDN (Pin 15/Pin 17): Shutdown Pin. In conjunction
with the UVLO (undervoltage lockout) circuit, this pin is
used to enable/disable the chip and restart the soft-start
sequence. Drive below 0.3V to disable the chip with very
low quiescent current. Drive above 1.33V (typical) to
activate the chip and restart the soft-start sequence. Do
not float this pin.
RT (Pin 16/Pin 18): Timing Resistor Pin. Adjusts the
LT3579’s switching frequency. Place a resistor from this
pin to ground to set the frequency to a fixed free running
level. Do not float this pin.
SYNC (Pin 17/Pin 20): To synchronize the switching
frequency to an outside clock, simply drive this pin with
a clock. The high voltage level of the clock must exceed
1.3V, and the low level must be less than 0.4V. Drive this
pin to less than 0.4V to revert to the internal free running
clock. See the Applications Information section for more
information.
SS (Pin 18/Pin 19): Soft-Start Pin. Place a soft-start
capacitor here. Upon start-up, the SS pin will be charged
by a (nominally) 250k resistor to ~2.1V. During a fault,
the SS pin will be slowly charged up and discharged as
part of a timeout sequence.
VC (Pin 19/Pin 2): Error Amplifier Output Pin. Tie external
compensation network to this pin.
FB (Pin 20/Pin 1): Positive and Negative Feedback Pin.
For a Boost or Inverting Converter, tie a resistor from the
FB pin to VOUT according to the following equations:
RFB =
VOUT –1.215V
83.3A
; Boost or SEPIC Converter
RFB =
| VOUT |+9mV
83.3A
;Inverting Converter
(QFN/TSSOP)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3521IFE#TRPBF | SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 |
| LS4501-9PD6TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LK2320-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK2540-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7EPD7T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3579EFE-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EFE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EFE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EUFD#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3579EUFD#TRPBF | 功能描述:IC REG MULTI CONFIG SYNC 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。