- 您现在的位置：买卖IC网 > PDF目录1825 > LT3640IFE#TRPBF (Linear Technology)IC REG BUCK FIX/ADJ DL 28TSSOP PDF资料下载
参数资料
| 型号： | LT3640IFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK FIX/ADJ DL 28TSSOP |
| 标准包装： | 2,000 |
| 类型： | 降压（降压） |
| 输出类型： | 两者兼有 |
| 输出数： | 2 |
| 输出电压： | 1.8V，3.3V，可调 |
| 输入电压： | 2.5 V ~ 35 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 500kHz ~ 2MHz |
| 电流 - 输出： | 1.1A，1.3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
LT3640
PIN FUNCTIONS
(FE/QFN)
FB2 (Pin 1/Pin 26): The low voltage converter regulates the
FB2 pin to 600mV. Connect the feedback resistor divider
tap to this pin to set output voltage.
PGOOD (Pin 2/Pin 27): Open-drain logic output that starts
to sink current when FB2 is in regulation.
EN/UVLO (Pin 3/Pin 28): Pull this pin below 0.3V to shut
down the LT3640. The 1.26V threshold can function as an
accurate undervoltage lockout, preventing the LT3640 from
operating until V IN voltage has reached the programmed
level.
SYNC (Pin 4/Pin 1): Driving the SYNC pin with an external
clock signal synchronizes both converters to the applied
frequency. The lowest external clock frequency should be
20% higher than the internal oscillator frequency.
SS1 (Pin 5/Pin 2): The SS1 pin sets the FB1 voltage ex-
ternally between 0V and 1.265V, providing soft-start and
tracking. Tie this pin 1.5V or higher to use the internal
1.265V reference. A capacitor to ground at this pin sets the
ramp time to regulated output voltage for the high voltage
converter. Use a resistor divider to track another supply.
FB1 (Pin 6/Pin 3): The high voltage converter regulates the
FB1 pin to 1.265V. Connect the feedback resistor divider
tap to this pin to set output voltage.
RT (Pin 7/Pin 4): Oscillator Resistor Input. Connecting a
resistor to ground from this pin sets the internal oscillator
frequency.
RST2 (Pin 8/Pin 5): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor after
FB2 goes above 550mV.
RST1 (Pin 9/Pin 6): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor after
FB1 goes above 1.165V.
WDO (Pin 10/Pin 7): Open-drain logic output that remains
asserted for the period set by the CPOR pin capacitor if
WDE is enabled and WDI pin is not driven by an appropri-
ate signal.
CWDT (Pin 11/Pin 8): Connect a capacitor to ground at
this pin to set watchdog timer.
CPOR (Pin 12/Pin 9): Connect a capacitor to ground at this
pin to set the power-on reset timer and WDO output timer.
WDE (Pin 13/Pin 10): Watchdog Enable Pin.
WDI (Pin 14/Pin 11): The WDI pin receives watchdog
signals from a microprocessor.
GND (Pins 15, 16, 23, 26, Exposed Pad Pin 29/Pins 12,
13, 20, 23, Exposed Pad Pin 29): Ground. These pins
must be soldered to PCB ground.
NC (Pin 17/Pin 14): Not Connected. This pin can be con-
nected to ground.
DA (Pin 18/Pin 15): The DA pin is used to sense the catch
diode current for current limit and protection. Connect this
pin to catch diode anode.
SW1 (Pin 19/Pin 16): Output of the High Voltage Internal
Power Switch. Connect this pin to the inductor and catch
diode cathode.
SW (Pin 20/Pin 17): The SW pin is used to charge the
boost capacitor. Connect this pin to the boost capacitor.
BST (Pin 21/Pin 18): The BST pin is used to provide a drive
voltage, higher than V IN pin voltage, to the high voltage
channel internal power switch. Connect an external boost
diode to this pin.
V IN (Pin 22/Pin 19): The V IN pin supplies current to
the LT3640’s internal circuitry and to the high voltage
channel internal power switch. This pin must be locally
bypassed.
V IN2 (Pin 24/Pin 21): The V IN2 pin supplies current to the
internal power MOSFET of the low voltage converter and
to the LT3640’s internal circuitry when V IN2 is above 3V.
SW2 (Pin 25/Pin 22): Switch Node of the Low Voltage
Converter. Connect this pin to an inductor.
EN2 (Pin 27/Pin 24): Low Voltage Converter Enable Pin.
Pull this pin below 0.3V to shut down the low voltage
converter. Pull this pin above 1.5V to enable the low volt-
age converter.
SS2 (Pin 28/Pin 25): The SS2 pin sets the FB2 voltage
externally between 0V and 0.6V, providing soft-start and
tracking. Tie this pin 0.8V or higher to use the internal
0.6V reference. A capacitor to ground at this pin sets the
ramp time to regulated output voltage for the low voltage
converter. Use a resistor divider to track another supply.
3640f
相关PDF资料 |
PDF描述 |
|---|---|
| LT3641HFE#TRPBF | IC REG BUCK SYNC ADJ DL 28TSSOP |
| LT3650IMSE-8.4#TRPBF | IC CHARGER LI-ION 8.4V 2A 12MSOP |
| LT3652EMSE#PBF | IC BATTERY CHARGER SOLAR 12MSOP |
| LT3653IDCB#TRPBF | IC REG BUCK ADJ 1.2A 8DFN |
| LT3663HMS8E-3.3#PBF | IC REG BUCK 3.3V 1.2A 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3640IUFD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
| LT3640IUFD#PBF | 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3640IUFD#TRPBF | 功能描述:IC REG BUCK FIX/ADJ DL 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT3640IUFDPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
| LT3640IUFDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Monolithic Buck Regulator with Power-On Reset and Watchdog Timer |
发布紧急采购，3分钟左右您将得到回复。