- 您现在的位置：买卖IC网 > PDF目录16001 > LT3650IMSE-8.2#PBF (Linear Technology)IC CHARGER LI-ION 8.2V 2A 12MSOP PDF资料下载
参数资料
| 型号： | LT3650IMSE-8.2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/22页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER LI-ION 8.2V 2A 12MSOP |
| 标准包装： | 37 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 9 V ~ 32 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TSSOP （0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 12-MSOP，裸露焊盘 |
| 包装： | 管件 |
LT3650-8.2/LT3650-8.4
APPLICATIONS INFORMATION
Preconditioning and Bad-Battery Fault
An LT3650 charger has a precondition mode, in which
charge current is limited to 15% of the programmed I MAX ,
as set by R SENSE . The precondition current corresponds
to 15mV across R SENSE .
Precondition mode is engaged while the voltage on the BAT
pin is below the precondition threshold (V BAT(PRE) ). Once
the BAT voltage rises above the precondition threshold,
normal full-current charging can commence. The LT3650
incorporates 1.5% of threshold hysteresis to prevent
mode glitching.
When the internal timer is used for termination, bad-
battery detection is engaged. This fault detection feature
is designed to identify failed cells. A bad-battery fault is
triggered when the voltage on BAT remains below the
precondition threshold for greater than one-eighth of a
full timer cycle (one-eighth EOC). A bad-battery fault is
also triggered if a normally charging battery re-enters
precondition mode after one-eighth EOC.
When a bad-battery fault is triggered, the charging cycle
is suspended, so the CHRG status pin becomes high
impedance. The FAULT pin is pulled low to signal a fault
detection. The RNG/SS pin is also pulled low during this
fault, to accommodate a graceful restart, in the event that
a soft-start function is incorporated (see the RNG/SS:
Soft-Start section).
Cycling the charger’s power or SHDN function initiates
a new charging cycle, but an LT3650 charger does not
require a reset. Once a bad-battery fault is detected, a new
timer charging cycle initiates when the BAT pin exceeds
the precondition threshold voltage. During a bad-battery
fault, 0.5mA is sourced from the charger; removing the
failed battery allows the charger output voltage to rise and
initiate a charge cycle reset. As such, removing a bad bat-
tery resets the LT3650, so a new charge cycle is started
by connecting another battery to the charger output.
Battery Temperature Fault: NTC
The LT3650 can accommodate battery temperature moni-
toring by using an NTC (negative temperature coefficient)
thermistor close to the battery pack. The temperature
monitoring function is enabled by connecting a 10kΩ
B = 3380 NTC thermistor from the NTC pin to ground. If
the NTC function is not desired, leave the pin unconnected.
The NTC pin sources 50μA, and monitors the voltage
dropped across the 10kΩ thermistor. When the voltage
on this pin is above 1.36V (0°C) or below 0.29V (40°C),
the battery temperature is out of range, and the LT3650
triggers an NTC fault. The NTC fault condition remains until
the voltage on the NTC pin corresponds to a temperature
within the 0°C to 40°C range. Both hot and cold thresholds
incorporate hysteresis that corresponds to 5°C.
If higher operational charging temperatures are desired,
the temperature range can be expanded by adding se-
ries resistance to the 10k NTC resistor. Adding a 0.91k
resistor will increase the effective temperature threshold
to 45°C.
During an NTC fault, charging is halted and both status
pins are pulled low. If timer termination is enabled, the
timer count is suspended and held until the fault condi-
tion is relieved. The RNG/SS pin is also pulled low during
this fault, to accommodate a graceful restart in the event
that a soft-start function is being incorporated (see the
RNG/SS: Soft-Start section).
Thermal Foldback
The LT3650 contains a thermal foldback protection feature
that reduces maximum charger output current if the IC
junction temperature approaches 125°C. In most cases,
on-chip temperatures servo such that any overtempera-
ture conditions are relieved with only slight reductions in
maximum charger current.
In some cases, the thermal foldback protection feature
can reduce charger currents below the C/10 threshold. In
applications that use C/10 termination (TIMER = 0V), the
LT3650 will suspend charging and enter standby mode
until the overtemperature condition is relieved.
36508284fd
16
相关PDF资料 |
PDF描述 |
|---|---|
| CCF0.25TB100 | CLEAN CUT FR 1/4" BLK/WHT 100' |
| ACC07DRTF-S13 | CONN EDGECARD 14POS DIP .100 SLD |
| RCC26DRXN | CONN EDGECARD 52POS DIP .100 SLD |
| RCC26DRXH | CONN EDGECARD 52POS DIP .100 SLD |
| RCC17DRTF | CONN EDGECARD 34POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3651 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage High Current Controller for Battery Charging and Power Management |
| LT3651-4.1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A High Voltage Monolithic 4A High Voltage |
| LT3651-4.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651-8.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A HIgh Voltage 2-Cell Li-Ion Battery Charger |
| LT3651-8.4 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A HIgh Voltage 2-Cell Li-Ion Battery Charger |
发布紧急采购，3分钟左右您将得到回复。