- 您现在的位置：买卖IC网 > PDF目录16001 > LT3650IMSE-8.2#PBF (Linear Technology)IC CHARGER LI-ION 8.2V 2A 12MSOP PDF资料下载
参数资料
| 型号： | LT3650IMSE-8.2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER LI-ION 8.2V 2A 12MSOP |
| 标准包装： | 37 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 9 V ~ 32 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TSSOP （0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 12-MSOP，裸露焊盘 |
| 包装： | 管件 |
LT3650-8.2/LT3650-8.4
OPERATION
OVERVIEW
LT3650 is a complete monolithic, mid-power, Li-Ion battery
charger, addressing high input voltage applications with
solutions that use a minimum of external components.
The IC uses a 1MHz constant-frequency, average current
mode step-down architecture.
The LT3650 incorporates a 2A switch that is driven by a
bootstrapped supply to maximize efficiency during charging
cycles. A wide input range allows the operation to full-
charge from 9V to 32V. A precision threshold shutdown
pin allows incorporation of UVLO functionality using a
simple resistor divider. The IC can also be put into a low
current shutdown mode, in which the input supply bias
is reduced to only 15μA.
The LT3650 incorporates several degrees of charge current
control freedom. The overall maximum charge current is
set using an external inductor current sense resistor. A
maximum charge current programming pin allows dynamic
manipulation of the battery charge current. The LT3650
also incorporates a system input supply current limit
control feature that servos the battery charge current to
accommodate overall system load requirements.
The LT3650 automatically enters a battery precondition
mode if the sensed battery voltage is very low. In this
mode, the charge current is reduced to 15% of the
programmed maximum, as set by the inductor sense
resistor, R SENSE . Once the battery voltage climbs
above the internally set precondition threshold, the IC
automatically increases the maximum charge current to
the full programmed value.
The LT3650 can use a charge current based C/10 termina-
tion scheme, which ends a charge cycle when the battery
charge current falls to one-tenth the programmed maxi-
mum charge current. The LT3650 also contains an internal
charge cycle control timer, for timer-based termination.
When using the internal timer, the IC combines C/10
detection with a programmable time constraint, during
which the charging cycle can continue beyond the C/10
level to “top-off” a battery. The charge cycle terminates
when a specific time elapses, typically three hours. When
the timer-based scheme is used, the IC also supports bad-
battery detection, which triggers a system fault if a battery
stays in precondition mode for more than one-eighth of
the total programmed charge cycle time.
Once charging is terminated and the LT3650 is not
actively charging, the IC automatically enters a low current
standby mode in which supply bias currents are reduced
to 85μA. If the battery voltage drops 2.5% from the full
charge float voltage, the LT3650 engages an automatic
charge cycle restart. The IC also automatically restarts a
new charge cycle after a bad-battery fault once the failed
battery is removed and replaced with another battery.
The LT3650 contains provisions for a battery temperature
monitoring circuit. This feature monitors battery tem-
perature by using a thermistor during the charging cycle,
suspends charging, and signals a fault condition if the
battery temperature moves outside a safe charging range.
The LT3650 contains two digital open-collector outputs,
which provide charger status and signal fault conditions.
These binary coded pins signal battery charging, standby
or shutdown modes, battery temperature faults and bad-
battery faults.
General Operation (See Block Diagram)
The LT3650 uses average current mode control architec-
ture, such that the IC servos directly to average charge
current. The LT3650 senses charger output voltage via the
BAT pin. The difference between the voltage on this pin
and an internal float voltage reference is integrated by the
voltage error amplifier (V-EA). This amplifier generates an
error voltage on its output (I TH ), which corresponds to the
average current sensed across the inductor current sense
resistor, R SENSE , which is connected between the SENSE
and BAT pins. The I TH voltage is then divided down by a
factor of 10, and imposed on the input of the current er-
ror amplifier (C-EA). The difference between this imposed
voltage and the current sense resistor voltage is integrated,
with the resulting voltage (V C ) used as a threshold that
is compared against an internally generated ramp. The
output of this comparison controls the charger’s switch.
36508284fd
9
相关PDF资料 |
PDF描述 |
|---|---|
| CCF0.25TB100 | CLEAN CUT FR 1/4" BLK/WHT 100' |
| ACC07DRTF-S13 | CONN EDGECARD 14POS DIP .100 SLD |
| RCC26DRXN | CONN EDGECARD 52POS DIP .100 SLD |
| RCC26DRXH | CONN EDGECARD 52POS DIP .100 SLD |
| RCC17DRTF | CONN EDGECARD 34POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3651 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage High Current Controller for Battery Charging and Power Management |
| LT3651-4.1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A High Voltage Monolithic 4A High Voltage |
| LT3651-4.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A High Voltage Li-Ion Battery Charger |
| LT3651-8.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A HIgh Voltage 2-Cell Li-Ion Battery Charger |
| LT3651-8.4 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Monolithic 4A HIgh Voltage 2-Cell Li-Ion Battery Charger |
发布紧急采购，3分钟左右您将得到回复。