参数资料
| 型号： | LT3682IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A 12DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 12-DFN |
LT3682
APPLICATIONS INFORMATION
where f SW is the switching frequency in MHz, V OUT is the
output voltage, V D is the catch diode drop (~0.5V) and L
is the inductor value in μH.
The current in the inductor is a triangle wave with an av-
erage value equal to the load current. The peak inductor
and switch current is:
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. To keep the ef?ciency high, the series
I SW ( PEAK ) = I L ( PEAK ) = I OUT ( MAX ) +
Δ I L
2
resistance (DCR) should be less than 0.1Ω, and the core
material should be intended for high frequency applications.
Table 1 lists several vendors and suitable types.
For robust operation in fault conditions (start-up or short
circuit) and high input voltage (>30V), the saturation
current should be chosen high enough to ensure that the
inductor peak current does not exceed 3.5A. For example,
an application running from an input voltage of 36V us-
ing a 10μH inductor with a saturation current of 2.5A will
tolerate the mentioned fault conditions.
where I L(PEAK) is the peak inductor current, I OUT(MAX) is
the maximum output load current, and Δ I L is the induc-
tor ripple current. The LT3682 limits its switch current in
order to protect itself and the system from overload faults.
Therefore, the maximum output current that the LT3682 will
deliver depends on the switch current limit, the inductor
value and the input and output voltages.
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A larger
value inductor provides a higher maximum load current and
Δ I L =
(1 ? DC) ?( V OUT + V D )
L ? f SW
reduces the output voltage ripple. If your load is lower than
the maximum load current, then you can relax the value of
the inductor and operate with higher ripple current. This
allows you to use a physically smaller inductor, or one with
a lower DCR resulting in higher ef?ciency. Be aware that
if the inductance differs from the simple rule above, then
the maximum load current will depend on input voltage.
In addition, low inductance may result in discontinuous
mode operation, which further reduces maximum load
current. For details of maximum output current and
discontinuous mode operation, see Linear Technology’s
Application Note 44. Finally, for duty cycles greater than
50% (V OUT /V IN > 0.5), a minimum inductance is required
to avoid sub-harmonic oscillations:
where f SW is the switching frequency of the LT3682, DC
is the duty cycle and L is the value of the inductor.
To maintain output regulation, the inductor peak current
must be less than the LT3682’s switch current limit I LIM .
If SYNC pin is grounded I LIM is at least 1.45A at low duty
cycles and decreases to 1.1A at DC = 90%. If SYNC pin
is tied to 0.8V or more or if it is tied to a clock source for
synchronization I LIM is at least 1.18A at low duty cycles
and decreases to 0.85A at DC = 90%. The maximum output
current is also a function of the chosen inductor value
and can be approximated by the following expressions
depending on the SYNC pin con?guration:
For SYNC pin grounded:
Δ I L Δ I L
L MIN = ( V OUT + V D ) ?
1.2
f SW
I OUT ( MAX ) = I LIM ?
2 2
= 1 . 45 A ?( 1 ? 0 . 24 ? DC ) ?
3682f
13
相关PDF资料 |
PDF描述 |
|---|---|
| LT3684IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT3685IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT3686HDD#TRPBF | IC REG BUCK ADJ 1.2A 10DFN |
| LT3688HFE#TRPBF | IC REG BUCK ADJ 0.8A DL 24TSSOP |
| LT3689EUD#PBF | IC REG BUCK ADJ 0.7A 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3684 | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 2.8MHz Step-Down Switching Regulator |
| LT3684EDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 2.8MHz Step-Down Switching Regulator |
| LT3684EDD#PBF | 功能描述:IC REG BUCK ADJ 2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3684EDD#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 2.8MHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 2.8MHZ, DFN-10 |
| LT3684EDD#TRPBF | 功能描述:IC REG BUCK ADJ 2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。