参数资料
| 型号： | LT3682IDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1A 12DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 20 V |
| 输入电压： | 3.6 V ~ 36 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 250kHz ~ 2.2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 12-DFN |
LT3682
APPLICATIONS INFORMATION
Δ I L Δ I L
I OUT ( MAX ) = I LIM ? = 1 . 1 8 A ?( 1 ? 0 . 29 ? DC ) ?
ForSYNCpintiedto0.8Vormore,ortiedtoaclocksource
for synchronization:
2 2
Choosing an inductor value so that the ripple current is
small will allow a maximum output current near the switch
current limit.
Table 1. Inductor Vendors
necessary. This can be provided with a lower performance
electrolytic capacitor.
Step-down regulators draw current from the input sup-
ply in pulses with very fast rise and fall times. The input
capacitor is required to reduce the resulting voltage
ripple at the LT3682 and to force this very high frequency
switching current into a tight local loop, minimizing EMI.
A 2.2μF capacitor is capable of this task, but only if it is
placed close to the LT3682 (see the PCB Layout section
VENDOR
Murata
TDK
URL PART SERIES
www.murata.com LQH55D
www.componenttdk.com SLF7045
SLF10145
TYPE
Open
Shielded
Shielded
for more information). A second precaution regarding
the ceramic input capacitor concerns the maximum input
voltage rating of the LT3682. A ceramic input capacitor
combined with trace or cable inductance forms a high-Q
Toko
Coilcraft
www.toko.com
www.coilcraft.com
D62CB
D63CB
D73C
D75F
MSS7341
Shielded
Shielded
Shielded
Open
Shielded
(underdamped) tank circuit. If the LT3682 circuit is plugged
into a live supply, the input voltage can ring to twice its
nominal value, possibly exceeding the LT3682’s voltage
rating. For details see Application Note 88.
MSS1038
Shielded
Sumida
www.sumida.com
CR54
CDRH74
CDRH6D38
CR75
Open
Shielded
Shielded
Open
Output Capacitor and Output Ripple
The output capacitor has two essential functions. Along
with the inductor, it ?lters the square wave generated by the
LT3682 to produce the DC output. In this role it determines
One approach to choosing the inductor is to start with the
simple rule given above, look at the available inductors,
and choose one to meet cost or space goals. Then use
these equations to check that the LT3682 will be able to
deliver the required output current. Note again that these
equations assume that the inductor current is continuous.
the output ripple, and low impedance at the switching
frequency is important. The second function is to store
energy in order to satisfy transient loads and stabilize the
LT3682’s control loop. Ceramic capacitors have very low
equivalent series resistance (ESR) and provide the best
ripple performance. A good starting value is:
V OUT SW
Discontinuous operation occurs when I OUT is less than
Δ I L /2.
C OUT =
50
f
Input Capacitor
Bypass the input of the LT3682 circuit with a ceramic capaci-
tor of X7R or X5R type. Y5V types have poor performance
over temperature and applied voltage, and should not be
used. A 2.2μF to 10μF ceramic capacitor is adequate to
bypass the LT3682 and will easily handle the ripple current.
Note that larger input capacitance is required when a lower
switching frequency is used. If the input power source has
high impedance, or there is signi?cant inductance due to
long wires or cables, additional bulk capacitance may be
where f SW is in MHz, and C OUT is the recommended
output capacitance in μF. Use X5R or X7R types. This
choice will provide low output ripple and good transient
response. Transient performance can be improved with
a higher value capacitor if the compensation network is
also adjusted to maintain the loop bandwidth. A lower
value of output capacitor can be used to save space
and cost but transient performance will suffer. See the
Frequency Compensation section to choose an appropriate
compensation network.
3682f
14
相关PDF资料 |
PDF描述 |
|---|---|
| LT3684IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT3685IMSE#TRPBF | IC REG BUCK ADJ 2A 10MSOP |
| LT3686HDD#TRPBF | IC REG BUCK ADJ 1.2A 10DFN |
| LT3688HFE#TRPBF | IC REG BUCK ADJ 0.8A DL 24TSSOP |
| LT3689EUD#PBF | IC REG BUCK ADJ 0.7A 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3684 | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 2.8MHz Step-Down Switching Regulator |
| LT3684EDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 2A, 2.8MHz Step-Down Switching Regulator |
| LT3684EDD#PBF | 功能描述:IC REG BUCK ADJ 2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3684EDD#PBF | 制造商:Linear Technology 功能描述:DC-DC CONVERTER BUCK 2.8MHZ 制造商:Linear Technology 功能描述:DC-DC CONVERTER, BUCK, 2.8MHZ, DFN-10 |
| LT3684EDD#TRPBF | 功能描述:IC REG BUCK ADJ 2A 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。