- 您现在的位置：买卖IC网 > PDF目录15501 > LT3845IFE#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16TSSOP PDF资料下载
参数资料
| 型号： | LT3845IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16TSSOP |
| 标准包装： | 95 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
LT3845
APPLICATIONS INFORMATION
will increase the peak currents, requiring more ?ltering
on the input and output of the supply. If ΔI L is too high,
the slope compensation circuit is ineffective and current
mode instability may occur at duty cycles greater than
50%. To satisfy slope compensation requirements the
minimum inductance is calculated as follows:
balancing the transition losses with the conduction losses
is a good idea while the bottom MOSFET is dominated by
the conduction loss, which is worse during a short-circit
condition or at a very low duty cycle.
Calculate the maximum conduction losses of the
MOSFETs:
2DC MAX – 1 R SENSE ? 8.33
L MIN >V OUT ?
DC MAX f SW
?
P COND(TOP) = I OUT(MAX)2 ?
V OUT
V IN
?R DS(ON)
The magnetics vendors specify either the saturation cur-
rent, the RMS current or both. When selecting an inductor
based on inductor saturation current, use the peak cur-
P COND(BOT) = I OUT(MAX)2 ?
V IN – V OUT
V IN
?R DS(ON)
rent through the inductor, I OUT(MAX) + ΔI L /2. The inductor
saturation current speci?cation is the current at which
the inductance, measured at zero current, decreases by
a speci?ed amount, typically 30%.
When selecting an inductor based on RMS current rating,
use the average current through the inductor, I OUT(MAX) .
The RMS current speci?cation is the RMS current at which
the part has a speci?c temperature rise, typically 40°C,
above 25°C ambient.
After calculating the minimum inductance value, the
volt-second product, the saturation current and the RMS
current for your design, select an off-the-shelf inductor.
Contact the Application group at Linear Technology for
further support.
For more detailed information on selecting an inductor,
please see the “Inductor Selection” section of Linear
Technology Application Note 44.
MOSFET Selection
The selection criteria of the external N-channel standard
level power MOSFETs include on resistance (R DS(ON) ),
reverse transfer capacitance (C RSS ), maximum drain
source voltage (V DSS ), total gate charge (Q G ) and maximum
continuous drain current.
For maximum ef?ciency, minimize R DS(ON) and C RSS .
Low R DS(ON) minimizes conduction losses while low C RSS
minimizes transition losses. The problem is that R DS(ON)
is inversely related to C RSS . In selecting the top MOSFET
Note that R DS(ON) has a large positive temperature depen-
dence. The MOSFET manufacturer’s data sheet contains a
curve, R DS(ON) vs Temperature.
In the main MOSFET, transition losses are proportional
to V IN2 and can be considerably large in high voltage ap-
plications (V IN > 20V). Calculate the maximum transition
losses:
P TRAN(TOP) = k ? V IN2 ? I OUT(MAX) ? C RSS ? f SW
where k is a constant inversely related to the gate driver
current, approximated by k = 2 for LT3845 applications.
The total maximum power dissipations of the MOSFET
are:
P TOP(TOTAL) = P COND(MAIN) + P TRAN(MAIN)
P BOT(TOTAL) = P COND(SYNC)
To achieve high supply ef?ciency, keep the total power dis-
sipation in each switch to less than 3% of the total output
power. Also, complete a thermal analysis to ensure that
the MOSFET junction temperature is not exceeded.
T J = T A + P (TOTAL) ? θ JA
where θ JA is the package thermal resistance and T A is the
ambient temperature. Keep the calculated T J below the max-
imum speci?ed junction temperature, typically 150°C.
Note that when V IN is high and f SW is high, the transition
losses may dominate. A MOSFET with higher R DS(ON)
and lower C RSS may provide higher ef?ciency. MOSFETs
with higher voltage V DSS speci?cation usually have higher
R DS(ON) and lower C RSS .
3845fd
15
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3785IUF#PBF | IC REG CTRLR BST PWM VM 24-QFN |
| LT3724IFE#PBF | IC REG CTRLR BST INV PWM 16TSSOP |
| LTC3862IUH#PBF | IC REG CTRLR BST PWM CM 24-QFN |
| LTC1709EG-8#PBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
| LTC1709EG-7#PBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3845IFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency |
| LT3845IFE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency |
| LT3845MPFE | 制造商:Linear Technology 功能描述:Step Down Controller 16-Pin TSSOP EP 制造商:Linear Technology 功能描述:HIGH VOLTAGE SYNCHRONOUSCURRENT MODE STEP-DOWNCONTROLLER WITH ADJUSTABLEOPERATING FREQUENCY |
| LT3845MPFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LT3845MPFE#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-DOWN CONTROLLER 16-TSSOP |
发布紧急采购，3分钟左右您将得到回复。