- 您现在的位置：买卖IC网 > PDF目录15501 > LT3845IFE#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16TSSOP PDF资料下载
参数资料
| 型号： | LT3845IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/26页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16TSSOP |
| 标准包装： | 95 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 电源电压： | 4 V ~ 60 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
LT3845
APPLICATIONS INFORMATION
Choose the MOSFET V DSS speci?cation to exceed the
maximum voltage across the drain to the source of the
MOSFET, which is V IN(MAX) plus any additional ringing
on the switch node. Ringing on the switch node can be
greatly reduced with good PCB layout and, if necessary,
an RC snubber.
In some applications, parasitic FET capacitances couple
the negative going switch node transient onto the bottom
gate drive pin of the LT3845, causing a negative voltage
in excess of the Absolute Maximum Rating to be imposed
on that pin. Connection of a catch Schottky diode from
The bulk capacitance is calculated based on maximum
input ripple, ΔV IN :
I OUT(MAX) ? V OUT
C IN(BULK) =
Δ V IN ? f SW ? V IN(MIN)
ΔV IN is typically chosen at a level acceptable to the user.
100mV to 200mV is a good starting point. Aluminum elec-
trolytic capacitors are a good choice for high voltage, bulk
capacitance due to their high capacitance per unit area.
The capacitor’s RMS current is:
this pin to ground will eliminate this effect. A 1A current
rating is typically suf?cient of the diode.
The internal V CC regulator is capable of sourcing up to
I CIN(RMS) = I OUT
V OUT (V IN – V OUT )
(V IN ) 2
40mA limiting the maximum total MOSFET gate charge,
Q G , to 35mA/f SW . The Q G vs V GS speci?cation is typically
provided in the MOSFET data sheet. Use Q G at V GS of 8V.
If V CC is back driven from an external supply, the MOSFET
drive current is not sourced from the internal regulator
of the LT3845 and the Q G of the MOSFET is not limited
by the IC. However, note that the MOSFET drive current
is supplied by the internal regulator when the external
supply back driving V CC is not available such as during
start-up or short circuit.
The manufacturer’s maximum continuous drain current
speci?cation should exceed the peak switch current,
I OUT(MAX) + ΔI L /2.
During the supply start-up, the gate drive levels are set by
the V CC voltage regulator, which is approximately 8V. Once
the supply is up and running, the V CC can be back driven
by an auxiliary supply such as V OUT . It is important not to
exceed the manufacturer’s maximum V GS speci?cation.
A standard level threshold MOSFET typically has a V GS
maximum of 20V.
Input Capacitor Selection
A local input bypass capacitor is required for buck convert-
ers because the input current is pulsed with fast rise and
If applicable, calculate it at the worst case condition,
V IN = 2V OUT . The RMS current rating of the capacitor
is speci?ed by the manufacturer and should exceed the
calculated I CIN(RMS) . Due to their low ESR (Equivalent
Series Resistance), ceramic capacitors are a good choice
for high voltage, high RMS current handling. Note that the
ripple current ratings from aluminum electrolytic capacitor
manufacturers are based on 2000 hours of life. This makes
it advisable to further derate the capacitor or to choose a
capacitor rated at a higher temperature than required.
The combination of aluminum electrolytic capacitors and
ceramic capacitors is an economical approach to meet-
ing the input capacitor requirements. The capacitor volt-
age rating must be rated greater than V IN(MAX) . Multiple
capacitors may also be paralleled to meet size or height
requirements in the design. Locate the capacitor very close
to the MOSFET switch and use short, wide PCB traces to
minimize parasitic inductance.
Output Capacitor Selection
The output capacitance, C OUT , selection is based on the
design’s output voltage ripple, ΔV OUT and transient load
requirements. ΔV OUT is a function of ΔI L and the C OUT
ESR. It is calculated by:
fall times. The input capacitor selection criteria are based
on the bulk capacitance and RMS current capability. The
bulk capacitance will determine the supply input ripple
voltage. The RMS current capability is used to prevent
overheating the capacitor.
16
V OUT = I L ? ESR +
1
(8 ? f SW ? C OUT )
3845fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3785IUF#PBF | IC REG CTRLR BST PWM VM 24-QFN |
| LT3724IFE#PBF | IC REG CTRLR BST INV PWM 16TSSOP |
| LTC3862IUH#PBF | IC REG CTRLR BST PWM CM 24-QFN |
| LTC1709EG-8#PBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
| LTC1709EG-7#PBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3845IFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency |
| LT3845IFE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency |
| LT3845MPFE | 制造商:Linear Technology 功能描述:Step Down Controller 16-Pin TSSOP EP 制造商:Linear Technology 功能描述:HIGH VOLTAGE SYNCHRONOUSCURRENT MODE STEP-DOWNCONTROLLER WITH ADJUSTABLEOPERATING FREQUENCY |
| LT3845MPFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LT3845MPFE#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-DOWN CONTROLLER 16-TSSOP |
发布紧急采购，3分钟左右您将得到回复。