参数资料
| 型号： | LT8415IDDB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 25MA 12DFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.5 V ~ 40 V |
| 输入电压： | 2.5 V ~ 16 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 800kHz |
| 电流 - 输出： | 25mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 12-DFN-EP（3x2） |
LT8415
APPLICATIONS INFORMATION
Maximum Output Load Current
The maximum output current of a particular LT8415 circuit
is a function of several circuit variables. The following
method can be helpful in predicting the maximum load
current for a given circuit:
Step 1: Calculate the peak inductor current:
Inrush Current
When V CC is stepped from ground to the operating voltage
while the output capacitor is discharged, a high level of
inrush current may ?ow through the inductor and Schottky
diode into the output capacitor. Conditions that increase
inrush current include a larger more abrupt voltage step
at V CC , a larger output capacitor tied to the CAP pin and
I PK = I LIMIT
+
V IN ? 150 ? 10 ? 6
L
mA
an inductor with a low saturation current. While the chip is
designed to handle such events, the inrush current should
not be allowed to exceed 0.3A. For circuits that use output
(V OUT + 1 ? V IN ) ? 200 ? 10 ? 6
I RIPPLE = mA
I RIPPLE
I IN(AVG) = I PK ? mA
whereI LIMIT is25mA.ListheinductancevalueinHenrys
and V IN is the input voltage to the boost circuit.
Step 2: Calculate the inductor ripple current:
L
where V OUT is the desired output voltage. If the inductor
ripple current is less than the peak current, then the circuit
will only operate in discontinuous conduction mode. The
inductor value should be increased so that I RIPPLE < I PK .
An application circuit can be designed to operate only in
discontinuous mode, but the output current capability
will be reduced.
Step 3: Calculate the average input current:
2
Step 4: Calculate the nominal output current:
capacitor values within the recommended range and have
input voltages of less than 6V, inrush current remains low,
posing no hazard to the device. In cases where there are
large steps at V CC (more than 6V) and/or a large capacitor
is used at the CAP pin, inrush current should be measured
to ensure safe operation.
Soft-Start
The LT8415 contains a soft-start circuit to limit peak switch
currents during start-up. High start-up current is inherent
in switching regulators in general since the feedback loop
is saturated due to V OUT being far from its ?nal value. The
regulator tries to charge the output capacitor as quickly
as possible, which results in large peak current.
When the FBP pin voltage is generated by a resistor divider
from the V REF pin, the start-up current can be limited by
connecting an external capacitor (typically 47nF to 220nF)
to the V REF pin. When the part is brought out of shutdown,
this capacitor is ?rst discharged for about 70μs (providing
protection against pin glitches and slow ramping), then
I OUT(NOM) =
I IN(AVG) ? V IN ? 0.7
V OUT
mA
an internal 10μA current source pulls the V REF pin slowly
to 1.235V. Since the V OUT voltage is set by the FBP pin
voltage, the V OUT voltage will also slowly increase to the
Step 5: Derate output current:
I OUT = I OUT(NOM) ? 0.8
For low output voltages the output current capability will
be increased. When using output disconnect (load current
taken from V OUT ), these higher currents will cause the
drop in the PMOS switch to be higher resulting in lower
output current capability than predicted by the preceding
equations.
regulated voltage, which results in lower peak inductor
current. The voltage ramp rate on the pin can be set by
the value of the V REF pin capacitor.
Output Disconnect
The LT8415 has an output disconnect PMOS that blocks
the load from the input during shutdown. The maximum
current through the PMOS is limited to 19mA by circuitry
inside the chip, helping the chip survive output shorts.
8415f
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT8582IDKD#TRPBF | IC REG MULTI CONFIG ADJ 3A 24DFN |
| LTC1043CSW#TRPBF | IC BUILDNG BLK SW-CAP DUAL18SOIC |
| LTC1044CS8#TRPBF | IC REG MULTI CONFIG 20MA 8SOIC |
| LTC1046IS8#TRPBF | IC REG SWITCHD CAP DIV INV 8SOIC |
| LTC1142LCG-ADJ#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT8500EUHH#PBF | 功能描述:IC PWM GENERATOR 56-QFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:1 系列:- 类型:时钟/频率发生器，多路复用器 PLL:是 主要目的:存储器，RDRAM 输入:晶体 输出:LVCMOS 电路数:1 比率 - 输入:输出:1:2 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:Digi-Reel® 其它名称:296-6719-6 |
| LT8500EUHH#TRPBF | 功能描述:IC PWM GENERATOR 56-QFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| LT8500IUHH#PBF | 功能描述:IC PWM GENERATOR 56-QFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| LT8500IUHH#TRPBF | 功能描述:IC PWM GENERATOR 56-QFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| LT-8501M | 制造商:Mencom 功能描述: |
发布紧急采购，3分钟左右您将得到回复。