- 您现在的位置：买卖IC网 > PDF目录9480 > LTC1092ACN8#PBF (Linear Technology)IC DAS SERIAL I/O 1CH 10BIT 8DIP PDF资料下载
参数资料
| 型号： | LTC1092ACN8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/32页 |
| 文件大小： | 0K |
| 描述： | IC DAS SERIAL I/O 1CH 10BIT 8DIP |
| 标准包装： | 50 |
| 类型： | 数据采集系统（DAS），ADC |
| 分辨率（位）： | 10 b |
| 数据接口： | 串行 |
| 电压电源： | 双 ± |
| 电源电压： | ±5V，4.5V，10V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
24
LTC1091/LTC1092
LTC1093/LTC1094
Figure 12. Reference Input Equivalent Circuit
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
Differential Inputs
With differential inputs, the A/D no longer converts just a
single voltage but rather the difference between two volt-
ages. In this case, the voltage on the selected “+” input is still
sampled and held and therefore may be rapidly time varying
just as in single-ended mode. However, the voltage on the
selected “–” input must remain constant and be free of noise
and ripple throughout the conversion time. Otherwise, the
differencing operation may not be performed accurately.
The conversion time is 10 CLK cycles. Therefore, a change
in the “–” input voltage during this interval can cause
conversion errors. For a sinusoidal voltage on the “–” input
this error would be:
VERROR(MAX) = (VPEAK)(2π) f(“–”)(10/fCLK)
Where f(“–”) is the frequency of the “–” input voltage,
VPEAK is its peak amplitude and fCLK is the frequency of the
CLK. In most cases VERROR will not be significant. For a
60Hz signal on the “–” input to generate a 0.25LSB error
(1.25mV) with the converter running at CLK = 500kHz, its
peak value would have to be 150mV.
5. Reference Inputs
The voltage between the reference inputs of the
LTC1091/LTC1092/LTC1093/LTC1094 defines the volt-
age span of the A/D converter. The reference inputs look
primarily like a 10k resistor but will have transient capaci-
tive switching currents due to the switched capacitor
conversion technique (see Figure 12). During each bit test
of the conversion (every CLK cycle), a capacitive current
spike will be generated on the reference pins by the A/D.
These current spikes settle quickly and do not cause a
problem. However, if slow settling circuitry is used to drive
the reference inputs, care must be taken to ensure that
transients caused by these current spikes settle com-
pletely during each bit test of the conversion.
When driving the reference inputs, three things should be
kept in mind:
1. The source resistance (ROUT) driving the reference
inputs should be low (less than 1
) to prevent DC
drops caused by the 1mA maximum reference current
(IREF).
2. Transients on the reference inputs caused by the
capacitive switching currents must settle completely
during each bit test (each CLK cycle). Figures 13 and
14 show examples of both adequate and poor settling.
Using a slower CLK will allow more time for the
reference to settle. However, even at the maximum
CLK rate of 500kHz most references and op amps can
be made to settle within the 2
s bit time.
3. It is recommended that the REF– input of the LTC1094
be tied directly to the analog ground plane. If REF– is
biased at a voltage other than ground, the voltage must
not change during a conversion cycle. This voltage
must also be free of noise and ripple with respect to
analog ground.
RON
5pF TO
30pF
10k
TYP
LTC1091/2/3/4
REF+
ROUT
VREF
EVERY CLK CYCLE
14
13
(AGND)
1091-4 F12
0.5mV/DIV
1
s/DIV
1091-4 F13
Figure 13. Adequate Reference Settling
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1092ACN8 | IC DAS SERIAL I/O 1CH 10BIT 8DIP |
| LTC1091ACN8#PBF | IC DATA ACQ SYS 10BIT 2CH 8-DIP |
| LTC1091ACN8 | IC DATA ACQ SYS 10BIT 2CH 8-DIP |
| AD7729ARUZ | IC ADC 15BIT DUAL W/DAC 28TSSOP |
| AD7729ARZ | IC ADC 15BIT DUAL W/DAC 28SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1092AMJ8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 10-Bit |
| LTC1092AMJ8/883 | 制造商:Linear Technology 功能描述: |
| LTC1092C | 制造商:LINER 制造商全称:Linear Technology 功能描述:1-, 2-, 6- and 8-Channel, 10-Bit Serial I/O Data Acquisition Systems |
| LTC1092CJ8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter， 10-Bit |
| LTC1092CN8 | 功能描述:IC DAS SERIAL I/O 1CH 10BIT 8DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - ADCs/DAC - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:数据采集系统（DAS） 分辨率（位）:16 b 采样率（每秒）:21.94k 数据接口:MICROWIRE?，QSPI?，串行，SPI? 电压电源:模拟和数字 电源电压:1.8 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。