- 您现在的位置：买卖IC网 > PDF目录9503 > LTC1287CCN8#PBF (Linear Technology)IC DATA ACQ SYS 12BIT 3V 8-DIP PDF资料下载
参数资料
| 型号： | LTC1287CCN8#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | IC DATA ACQ SYS 12BIT 3V 8-DIP |
| 标准包装： | 50 |
| 类型： | 数据采集系统（DAS） |
| 分辨率（位）： | 12 b |
| 采样率（每秒）： | 30k |
| 数据接口： | 串行，并联 |
| 电压电源： | 单电源 |
| 电源电压： | 3V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
12
LTC1287
1287fa
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
RC Input filtering
It is possible to filter the inputs with an RC network as
shown in Figure 11. For large values of CF (e.g., 1F) the
capacitive input switching currents are averaged into a net
DC current. A filter should be chosen with a small resistor
and large capacitor to prevent DC drops across the resistor.
The magnitude of the DC current is approximately IDC =
100pF
× VIN/tCYC and is roughly proportional to VIN. When
running at the minimum cycle time of 33
s, the input
current equals 7.6
A at VIN = 2.5V. Here a filter resistor of
8
will cause 0.1LSB of full-scale error. If a large filter
resistor must be used, errors can be reduced by increasing
the cycle time as shown in the Typical Performance
Characteristics curve Maximum Filter Resistor vs Cycle
Time.
Figure 11. RC Input Filtering
Input Leakage Current
Input leakage currents also can create errors if the source
resistance gets too large. For example, the maximum input
leakage specification of 1
A (at 85°C) flowing through a
source resistance of 1k will cause a voltage drop of 1mV
or 1.6LSB with VREF = 2.5V. This error will be much
reduced at lower temperatures because leakage drops
rapidly (see Typical Performance Characteristics curve
Input Channel Leakage Current vs Temperature).
SAMPLE-AND-HOLD
Single-Ended Input
The LTC1287 provides a built-in sample and hold (S&H)
function on the +IN input for signals acquired in the single
ended mode (–IN pin grounded). The sample and hold
allows the LTC1287 to convert rapidly varying signals (see
Typical Performance Characteristics curve of S&H
Acquisition Time vs Source Resistance). The input voltage
is sampled during the tSMPL time as shown in Figure 8. The
sampling interval begins at rising edge of CS and continues
until the falling edge of the CLK before the conversion
begins. On this falling edge the S&H goes into the hold
mode and the conversion begins.
Differential Input
With a differential input the A/D no longer converts a single
voltage but converts the difference between two voltages.
The voltage on the +IN pin is sampled and held and can be
rapidly time varying. The voltage on the –IN pin must
remain constant and be free of noise and ripple throughout
the conversion time. Otherwise the differencing operation
will not be done accurately. The conversion time is 12 CLK
cycles. Therefore a change in the –IN input voltage during
this interval can cause conversion errors. For a sinusoidal
voltage on the –IN input this error would be:
Where f(–IN) is the frequency of the –IN input voltage,
VPEAK is its peak amplitude and fCLK is the frequency of the
CLK. Usually VERROR will not be significant. For a 60Hz
signal on the –IN input to generate a 0.25LSB error
(150
V) with the converter running at CLK = 500kHz, its
peak value would have to be 16mV. Rearranging the above
equation, the maximum sinusoidal signal that can be
digitized to a given accuracy is given as:
For 0.25LSB error (150
V) the maximum input sinusoid
with a 2.5V peak amplitude that can be digitized is 0.4Hz.
Reference Input
The voltage on the reference input of the LTC1287
determines the voltage span of the A/D converter. The
reference input has transient capacitive switching cur-
rents due to the switched capacitor conversion tech-
nique (see Figure 12). During each bit test of the
RFILTER
VIN –
CFILTER
LTC1287 F11
LTC1287
“+”
“–”
IDC
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1287CCN8 | IC DATA ACQ SYS 12BIT 3V 8-DIP |
| VI-25L-MY-S | CONVERTER MOD DC/DC 28V 50W |
| VI-253-MY-S | CONVERTER MOD DC/DC 24V 50W |
| AD2S1210BSTZ | IC CONV R/D 10-16BIT 48-LQFP |
| V110A24M300B | CONVERTER MOD DC/DC 24V 300W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1288CN8 | 功能描述:IC A/D CONV SAMPLING 12BIT 8-DIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1288CN8#PBF | 功能描述:IC A/D CONV SAMPLING 12BIT 8-DIP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC1288CN8PBF | 制造商:Linear Technology 功能描述:LTC1288CN8PBF |
| LTC1288CS8 | 功能描述:IC A/D CONV SAMPLING 12BIT 8SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1288CS8#PBF | 功能描述:IC A/D CONV SAMPLING 12BIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。