- 您现在的位置：买卖IC网 > PDF目录15972 > LTC1325CSW (Linear Technology)IC BATTERY MANAGMNT SYSTEM18SOIC PDF资料下载
参数资料
| 型号： | LTC1325CSW |
| 厂商： | Linear Technology |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY MANAGMNT SYSTEM18SOIC |
| 标准包装： | 40 |
| 功能： | 充电管理 |
| 电池化学： | 铅酸，锂离子，镍镉，镍氢 |
| 电源电压： | 4.5 V ~ 16 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 18-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 18-SOIC |
| 包装： | 管件 |
| 其它名称： | LTC1325CS |
LTC1325
APPLICATIO N S I N FOR M ATIO N
where,
I F = forward diode current,
I F ′ = forward diode current just prior to turn off,
d. Thermistor Divider Temperature Curve
Typical temperature limits for both NiCd and NiMH
batteries are shown below.
V F = forward drop,
BATTERY
DISCHARGE TEMP
RANGE ( ° C)
CHARGE TEMP
RANGE ( ° C)
V R = reverse diode voltage (approximately equal to V DD ),
f = PWM frequency (111kHz), and
t RR = reverse recovery time
The power and maximum reverse voltage ratings of the
TYPE
Standard
Quick
Fast or Rapid
Trickle
MIN
– 20
– 20
– 20
– 20
MAX
45 to 50
45 to 50
45 to 50
45 to 50
MIN
0
10
15
0
MAX
45 to 50
45 to 50
45 to 50
45 to 50
diode should be greater than P dD1 and V DD respectively.
The catch diode should also have fast turn-on times to
reduce the voltage glitch at its cathode when turning on.
Schottky diodes have fast switching times and low
forward drops and are recommended for D1.
5. Trickle Resistor R TRK : R TRK sets the desired trickle
current in the battery to compensate for self-dis-
charge which is in the order 1% and 2% of capacity per
day for NiCd and NiMH batteries respectively. Trickle
charge rates are typically in the C/30 to C/50 range,
where C is battery capacity.
I TRK = (V DD – V BAT )/R TRK
where V BAT is the voltage of a full charged battery.
Note that I TRK varies as the battery is being charged.
6. Thermistor R T and Load R L : The total resistance of the
thermistor network should be greater than 30k at the
high temperature extreme to minimize effects of load
regulation (see REG pin loading).
7. Fault Setting Resistors R1, R2, R3 and R4: The voltage
levels at the LTF, HTF and MCV pins are tapped from
a resistor divider powered by the REG pin. The voltage
levels are selected taking into account:
a. Manufacturer Recommended Temperature and
Voltage limits,
b. Loading on the REG Pin (< 2mA)
c. Input Voltage Ranges of the LTF, HTF and MCV
Comparators:
1.6V < V LTF , V MCV < 2.8V and 0.5V < V HTF < 1.3V
Note that the discharge limits are wider than the
charge limits. To prolong battery life, manufacturers
generally recommend discharge temperatures that
are similar to the charge limits. For this reason, the
LTC1325 recognizes the same LTF and HTF limits in
both charge and discharge modes. MCV should be set
just above the charging voltage per cell given in
battery specifications. The voltage at the LTF and HTF
pins should be set to correspond to narrowest tem-
perature range. These are typically 15 ° C and 45 ° C.
The corresponding voltages may be read from the
thermistor divider temperature curve such as that
shown in Figure 5. For this thermistor, it works out to
be about for 2.12V for LTF and for 1.13V for HTF. The
MCV may be conveniently tied to LTF since MCV is
typically 2V. If desired, external analog switches under
microprocessor control may be used to vary the LTF,
HTF and MCV voltages between modes or for different
charge rates. The values of R1, R2, R3 and R4 in Figure
3 can be calculated from the following equations:
R4 = V HTF (RE/V REG )
R3 = V MCV (RE – R4)
R2 = V LTF (RE) – (R3 + R4)
R1 = RE – (R2 + R3 + R4)
where RE = R1 + R2 + R3 + R4 is chosen to minimize
loading on the REG pin. A minimum value of 30k is
recommended. Note that V LTF is assumed to be greater
than V MCV . If this is not the case, V LTF and V MCV in the
above equations should be swapped. If the MCV and
LTF pins are shorted to the same point, R2 should be
set to 0.
19
相关PDF资料 |
PDF描述 |
|---|---|
| ESM11DRYN-S13 | CONN EDGECARD 22POS .156 EXTEND |
| SDR0703-102KL | INDUCTOR POWER 1000UH SMD |
| ESM11DRYH-S13 | CONN EDGECARD 22POS .156 EXTEND |
| MAX6302CPA+ | IC SUPERVISOR MPU 8-DIP |
| EEC20DREI-S93 | CONN EDGECARD 40POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1325CSW#PBF | 功能描述:IC BATTERY MANAGMNT SYSTEM18SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC1325CSW#TR | 功能描述:IC SYSTEM BATT MANAGEMENT 18SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC1325CSW#TRPBF | 功能描述:IC BATTERY MANAGMNT SYSTEM18SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC1326CMS8 | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC1326CMS8#PBF | 功能描述:IC PREC TRPL SUPPLY MONITR 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。