- 您现在的位置：买卖IC网 > PDF目录10667 > LTC1408CUH#PBF (Linear Technology)IC ADC 14BIT 600KSPS 32-QFN PDF资料下载
参数资料
| 型号： | LTC1408CUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 600KSPS 32-QFN |
| 标准包装： | 73 |
| 位数： | 14 |
| 采样率（每秒）： | 600k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 15mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
| 输入数目和类型： | 12 个单端，单极；12 个单端，双极；6 个差分，单极；6 个差分，双极 |
| 产品目录页面： | 1346 (CN2011-ZH PDF) |
| 配用： | DC887A-ND - BOARD SAR ADC LTC1408 |
14
LTC1408
1408fa
APPLICATIO S I FOR ATIO
WU
UU
INPUT FILTERING AND SOURCE IMPEDANCE
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC1408 noise and distortion. The small-signal band-
width of the sample-and-hold circuit is 50MHz. Any noise
or distortion products that are present at the analog inputs
will be summed over this entire bandwidth. Noisy input
circuitry should be filtered prior to the analog inputs to
minimize noise. A simple 1-pole RC filter is sufficient for
many applications. For example, Figure 1 shows a 47pF
capacitor from CHO+ to ground and a 51
source resistor
to limit the net input bandwidth to 30MHz. The 47pF ca-
pacitor also acts as a charge reservoir for the input sample-
and-hold and isolates the ADC input from sampling-glitch
sensitive circuitry. High quality capacitors and resistors
should be used since these components can add distor-
tion. NPO and silvermica type dielectric capacitors have
excellent linearity. Carbon surface mount resistors can
generate distortion from self heating and from damage
that may occur during soldering. Metal film surface mount
resistors are much less susceptible to both problems.
When high amplitude unwanted signals are close in
frequency to the desired signal frequency a multiple pole
filter is required.
High external source resistance, combined with 13pF of
input capacitance, will reduce the rated 50MHz input band-
width and increase acquisition time beyond 39ns.
INPUT RANGE
The analog inputs of the LTC1408 may be driven fully
differentially with a single supply. Either input may swing
up to VCC, provided the differential swing is no greater than
2.5V with BIP (Pin 29) Low, or
±1.25V with (BIP Pin 29)
High. The 0V to 2.5V range is also ideally suited for single-
ended input use with single supply applications. The
common mode range of the inputs extend from ground to
the supply voltage VCC. If the difference between the CH+
and CH– at any input pair exceeds 2.5V (unipolar) or 1.25V
(bipolar), the output code will stay fixed at positive full-
scale, and if this difference goes below 0V (unipolar) or –
1.25V (bipolar), the output code will stay fixed at negative
full-scale.
INTERNAL REFERENCE
The LTC1408 has an on-chip, temperature compensated,
bandgap reference that is factory trimmed near 2.5V to
obtain a precise 2.5V input span. The reference amplifier
output VREF, (Pin 23) must be bypassed with a capacitor
to ground. The reference amplifier is stable with capaci-
tors of 1
F or greater. For the best noise performance, a
10
F ceramic or a 10F tantalum in parallel with a 0.1F
ceramic is recommended. The VREF pin can be overdriven
with an external reference as shown in Figure 2. The volt-
age of the external reference must be higher than the 2.5V
of the open-drain P-channel output of the internal refer-
ence. The recommended range for an external reference
is 2.55V to VDD. An external reference at 2.55V will see a
DC quiescent load of 0.75mA and as much as 3mA
Figure 1. RC Input Filter
LTC1408
CH0+
CH0–
VREF
GND
1408 F01
1
2
11
3
10
F
47pF*
51
*
CH1+
CH1–
4
5
47pF*
*TIGHT TOLERANCE REQUIRED TO AVOID
APERTURE SKEW DEGRADATION
51
*
ANALOG
INPUT
ANALOG
INPUT
Figure 2. External Reference
LTC1408
VREF
GND
1408 F02
23
22
10
F
3V REF
相关PDF资料 |
PDF描述 |
|---|---|
| MC10E1651FNR2G | IC COMPARATOR DUAL ECL 20-PLCC |
| AD9204BCPZ-80 | IC ADC 10BIT 80MSPS DL 64LFCSP |
| LTC2226IUH#PBF | IC ADC 12BIT 25MSPS SAMPL 32-QFN |
| MC10E1652FNR2G | IC COMPARATOR DUAL ECL 20PLCC |
| AD7714ANZ-5 | IC ADC SIGNAL COND 5V 24-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1408IUH#PBF | 功能描述:IC ADC 14BIT 600KSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC1408IUH#TRPBF | 功能描述:IC ADC 14BIT 600KSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| LTC1408IUH-12#PBF | 功能描述:IC ADC 12BIT 600KSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| LTC1408IUH-12#TRPBF | 功能描述:IC ADC 12BIT 600KSPS 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC1409CG | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。