参数资料
型号: LTC1628IG-SYNC#TR
厂商: LINEAR TECHNOLOGY CORP
元件分类: 稳压器
英文描述: 3 A SWITCHING CONTROLLER, 360 kHz SWITCHING FREQ-MAX, PDSO28
封装: 0.209 INCH, PLASTIC, SSOP-28
文件页数: 11/32页
文件大小: 658K
代理商: LTC1628IG-SYNC#TR
19
LTC1628-SYNC
1628syncfa
Rk
V
VV
MAX
OUT
124
08
24
()
.
.–
=
for VOUT < 2.4V
Regulating an output voltage of 1.8V, the maximum value
of R1 should be 32K. Note that for an output voltage above
2.4V, R1 has no maximum value necessary to absorb the
sense currents; however, R1 is still bounded by the
VOSENSE feedback current.
Soft-Start/Run Function
The RUN/SS1 and RUN/SS2 pins are multipurpose pins
that provide a soft-start function and a means to shut
down the LTC1628-SYNC. Soft-start reduces the input
power source’s surge currents by gradually increasing the
controller’s current limit (proportional to VITH). This pin
can also be used for power supply sequencing.
An internal 1.2
A current source charges up the CSS
capacitor. When the voltage on RUN/SS1 (RUN/SS2)
reaches 1.5V, the particular controller is permitted to start
operating. As the voltage on RUN/SS increases from 1.5V
to 3.0V, the internal current limit is increased from 25mV/
RSENSE to 75mV/RSENSE. The output current limit ramps
up slowly, taking an additional 1.25s/
F to reach full
current. The output current thus ramps up slowly, reduc-
ing the starting surge current required from the input
power supply. If RUN/SS has been pulled all the way to
ground there is a delay before starting of approximately:
t
V
A
Cs
F C
DELAY
SS
=
=
()
15
12
125
.
./
t
VV
A
Cs
F C
IRAMP
SS
=
=
()
31 5
12
125
.
./
By pulling both RUN/SS pins below 1V, the LTC1628-
SYNC is put into low current shutdown (IQ = 20A). The
RUN/SS pins can be driven directly from logic as shown
in Figure 7. Diode D1 in Figure 7 reduces the start delay
but allows CSS to ramp up slowly providing the soft-start
function. Each RUN/SS pin has an internal 6V zener clamp
(See Functional Diagram).
Fault Conditions: Overcurrent Latchoff
The RUN/SS pins also provide the ability to latch off the
controller(s) when an overcurrent condition is detected.
The RUN/SS capacitor, CSS, is used initially to turn on and
limit the inrush current. After the controller has been
started and been given adequate time to charge up the
output capacitor and provide full load current, the RUN/SS
capacitor is used for a short-circuit timer. If the regulator’s
output voltage falls to less than 70% of its nominal value
after CSS reaches 4.1V, CSS begins discharging on the
assumption that the output is in an overcurrent condition.
If the condition lasts for a long enough period as deter-
mined by the size of the CSS and the specified discharge
current, the controller will be shut down until the RUN/SS
pin voltage is recycled. If the overload occurs during start-
up, the time can be approximated by:
tLO1 ≈ [CSS(4.1 – 1.5 + 4.1 – 3.5)]/(1.2A)
= 2.7 106 (CSS)
If the overload occurs after start-up the voltage on CSS will
begin discharging from the zener clamp voltage:
tLO2 ≈ [CSS (6 – 3.5)]/(1.2A) = 2.1 106 (CSS)
This built-in overcurrent latchoff can be overridden by
providing a pull-up resistor to the RUN/SS pin as shown
in Figure 7. This resistance shortens the soft-start period
and prevents the discharge of the RUN/SS capacitor
during an over current condition. Tying this pull-up resis-
tor to VIN as in Figure 7a, defeats overcurrent latchoff.
Diode-connecting this pull-up resistor to INTVCC, as in
Figure 7b, eliminates any extra supply current during
controller shutdown while eliminating the INTVCC loading
from preventing controller start-up.
Figure 7. RUN/SS Pin Interfacing
3.3V OR 5V
RUN/SS
VIN
INTVCC
RUN/SS
D1
CSS
RSS*
CSS
RSS*
1628 F07
(a)
(b)
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料
PDF描述
LTC1643HCGN#PBF 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
LTC1643LCGN#TR 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
LTC1728HS5-5 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
LTC1729CS8-8.4#TR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
LTC1772BIS6#PBF 1 A SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO6
相关代理商/技术参数
参数描述
LTC1628IUH 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC1628IUH#PBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC1628IUH#TR 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC1628IUH#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC1629CG 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX