- 您现在的位置：买卖IC网 > PDF目录13074 > LTC1753CSW#TR (Linear Technology)IC REG SW 5BIT PROG SYNC 20SOIC PDF资料下载
参数资料
| 型号： | LTC1753CSW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | IC REG SW 5BIT PROG SYNC 20SOIC |
| 标准包装： | 1,000 |
| 应用： | 控制器，Intel Pentium? III |
| 输入电压： | 5V |
| 输出数： | 1 |
| 输出电压： | 1.3 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 带卷 (TR) |
LTC1753
TYPICAL PERFOR A CE CHARACTERISTICS
V OUT
20mV/DIV
G1
10V/DIV
Expanded View of Undershoot
Illustrates 100% Duty Cycle
Operation, V OUT = 2.8V
V OUT
20mV/DIV
G1
10V/DIV
Expanded View of Overshoot
Illustrates 0% Duty Cycle
Operation, V OUT = 2.8V
5 μ s/DIV
1753 G18
5 μ s/DIV
1753 G19
PI FU CTIO S
G2 (Pin 1): Gate Drive for the Lower N-Channel MOSFET,
Q2. This output will swing from PV CC to GND. It will always
be low when G1 is high or when the output is disabled. To
prevent undershoot during a soft-start cycle, G2 is held
low until G1 first goes high.
PV CC (Pin 2): Power Supply for G1 and G2. PV CC must be
connected to a potential of at least V IN + V GS(ON)Q1 . For
normal applications, connect PV CC to a 12V power supply
or generate PV CC using a simple charge pump.
GND (Pin 3): Power Ground. GND should be connected to
a low impedance ground plane in close proximity to the
source of Q2.
SGND (Pin 4): Signal Ground. SGND is connected to the
low power internal circuitry and should be connected to
the negative terminal of the output capacitor where it
returns to the ground plane. GND and SGND should be
shorted directly at the LTC1753.
V CC (Pin 5): Power Supply. Power for the internal low
power circuity. V CC should be wired separately from the
drain of Q1 if they share the same supply. A 10 μ F bypass
capacitor is recommended from this pin to SGND.
SENSE (Pin 6): Output Voltage Pin. Connect to the positive
terminal of the output capacitor. There is an internal 108k
resistor connected from this pin to SGND. SENSE is a very
sensitive pin; for optimum performance, connect an exter-
nal 1 μ F capacitor from this pin to SGND. By connecting a
small external resistor between the output capacitor and
the SENSE pin, the initial output voltage can be raised
slightly. Since the internal divider has a nominal imped-
ance of 108k ? , a 1100 ? series resistor will raise the
nominal output voltage by 1%. If an external resistor is
used, the value of the 1 μ F capacitor on the SENSE pin must
be greatly reduced or loop phase margin will suffer. Set a
time constant for the RC combination of approximately
0.1 μ s. So, for example, with a 1100 ? resistor, set
C = 90pF. Use a standard 100pF capacitor. In addition, LTC
recommends that the 1 μ F capacitor be connected from the
top of the additional external resistor directly to SGND.
I MAX (Pin 7): Current Limit Threshold. Current limit is set
by the voltage drop across an external resistor connected
between the drain of Q1 and I MAX . There is a 190 μ A internal
pull-down at I MAX .
I FB (Pin 8): Current Limit Sense Pin. Connect to the
switching node between the source of Q1 and the drain of
Q2. If I FB drops below I MAX when G1 is on, the LTC1753
will go into current limit. The current limit circuit can be
disabled by floating I MAX and shorting I FB to V CC .
SS (Pin 9): Soft-Start. Connect to an external capacitor to
implement a soft-start function. During moderate over-
load conditions, the soft-start capacitor will be discharged
slowly in order to reduce the duty cycle. In hard current
limit, the soft-start capacitor will be forced low immedi-
ately and the LTC1753 will rerun a complete soft-start
cycle. C SS must be selected such that during power-up the
current through Q1 will not exceed the current limit value.
1753fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J4P-CZ-B1 | CONVERTER MOD DC/DC 13.8V 25W |
| ACC26DRTI | CONN EDGECARD 52POS .100 DIP SLD |
| LTC1530CS8-3.3#PBF | IC SW REG CNTRLR SYNC 3.3V 8SOIC |
| VI-J4N-CZ-B1 | CONVERTER MOD DC/DC 18.5V 25W |
| 1812-274J | INDUCTOR UNSHIELDED 270UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1754ES6-3.3 | 制造商:Linear Technology 功能描述:Charge Pump STPUP 3.3V 40mA 6-Pin TSOT-23 |
| LTC1754ES6-3.3#PBF | 制造商:Linear Technology 功能描述:Charge Pump STPUP 3.3V 40mA 6-Pin TSOT-23 |
| LTC1754ES6-3.3#TR | 功能描述:IC REG SWITCHED CAP 3.3V SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| LTC1754ES6-3.3#TRM | 功能描述:IC REG SWITCHED CAP 3.3V SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
| LTC1754ES6-3.3#TRMPBF | 功能描述:IC REG SWITCHED CAP 3.3V SOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:500 系列:- 类型:切换式电容器（充电泵），反相 输出类型:固定 输出数:1 输出电压:-3V 输入电压:2.3 V ~ 5.5 V PWM 型:Burst Mode? 频率 - 开关:900kHz 电流 - 输出:100mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 包装:带卷 (TR) 供应商设备封装:TSOT-23-6 其它名称:LTC1983ES6-3#TRMTR |
发布紧急采购，3分钟左右您将得到回复。