- 您现在的位置：买卖IC网 > PDF目录10688 > LTC2435-1CGN#PBF (Linear Technology)IC ADC DIFF I/REF 20BIT 16-SSOP PDF资料下载
参数资料
| 型号： | LTC2435-1CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/42页 |
| 文件大小： | 0K |
| 描述： | IC ADC DIFF I/REF 20BIT 16-SSOP |
| 标准包装： | 100 |
| 位数： | 20 |
| 采样率（每秒）： | 13.75 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC2435/LTC2435-1
18
24351fc
For more information www.linear.com/LTC2435
applicaTions inForMaTion
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 13) is used to
synchronize the data transfer. Each bit of data is shifted
out the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is
an output and the LTC2435/LTC2435-1 create their own
serial clock by dividing the internal conversion clock by
8. In the External SCK mode of operation, the SCK pin
is used as input. The internal or external SCK mode is
selected on power-up and then reselected every time a
HIGH-to-LOW transition is detected at the CS pin. If SCK
is HIGH or floating at power-up or during this transition,
the converter enters the internal SCK mode. If SCK is LOW
at power-up or during this transition, the converter enters
the external SCK mode.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 12), provides the
result of the last conversion as a serial bit stream (MSB
first) during the data output state. In addition, the SDO
pin is used as an end of conversion indicator during the
conversion and sleep states.
When CS (Pin 11) is HIGH, the SDO driver is switched
to a high impedance state. This allows sharing the serial
interfacewithotherdevices.IfCSisLOWduringtheconvert
or sleep state, SDO will output EOC. If CS is LOW during
the conversion phase, the EOC bit appears HIGH on the
SDOpin.Oncetheconversioniscomplete,EOCgoesLOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 11), is used to test the
conversion status and to enable the data output transfer
as described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2435/LTC2435-1 will abort any
serial data transfer in progress and start a new conver-
sion cycle anytime a LOW-to-HIGH transition is detected
at the CS pin after the converter has entered the data
output state (i.e., after the first rising edge of SCK occurs
with CS = LOW).
Finally, CS can be used to control the free-running modes
of operation, see Serial Interface Timing Modes section.
Grounding CS will force the ADC to continuously convert
at the maximum output rate selected by FO.
SERIAL INTERFACE TIMING MODES
The LTC2435/LTC2435-1 3-wire interface is SPI and MI-
CROWIREcompatible.Thisinterfaceoffersseveralflexible
modes of operation. These include internal/external serial
clock, 2- or 3-wire I/O, single cycle conversion and auto-
start. The following sections describe each of these serial
interface timing modes in detail. In all these cases, the
converter can use the internal oscillator (FO = LOW or FO
= HIGH) or an external oscillator connected to the FO pin.
Refer to Table 4 for a summary.
Table 4. LTC2435/LTC2435-1 Interface Timing Modes
Configuration
SCK
Source
Conversion
Cycle
Control
Data
Output
Control
Connection
and
Waveforms
External SCK, Single Cycle Conversion
External
CS and SCK
Figures 8, 9
External SCK, 2-Wire I/O
External
SCK
Figure 10
Internal SCK, Single Cycle Conversion
Internal
CS
↓
CS
↓
Figures 11, 12
Internal SCK, 2-Wire I/O, Continuous Conversion
Internal
Continuous
Internal
Figure 13
相关PDF资料 |
PDF描述 |
|---|---|
| AD8611ARZ-REEL7 | IC COMP SGL 4NS ULTRFAST 8SOIC |
| AD7823YRZ | IC ADC 8BIT SRL 2.7/5.5V 8-SOIC |
| LTC1540IMS8#TRPBF | IC COMP NANOPOWER W/REF 8-MSOP |
| ISL4489EIBZ | TRANSCEIVER RS-485/422 14-SOIC |
| LTC1540IMS8#TR | IC COMP 300NA 2% VOLT REF 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2435-1IGN | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN#PBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN#TR | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2435-1IGN#TRPBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2435CGN | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。