- 您现在的位置：买卖IC网 > PDF目录10688 > LTC2435-1CGN#PBF (Linear Technology)IC ADC DIFF I/REF 20BIT 16-SSOP PDF资料下载
参数资料
| 型号： | LTC2435-1CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 5/42页 |
| 文件大小： | 0K |
| 描述： | IC ADC DIFF I/REF 20BIT 16-SSOP |
| 标准包装： | 100 |
| 位数： | 20 |
| 采样率（每秒）： | 13.75 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，双极 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC2435/LTC2435-1
13
24351fc
For more information www.linear.com/LTC2435
applicaTions inForMaTion
The LTC2435/LTC2435-1 perform a full-scale calibration
every conversion cycle. This calibration is transparent to
theuserandhasnoeffectonthecyclicoperationdescribed
above. The advantage of continuous calibration is extreme
stability of full-scale readings with respect to time, supply
voltage change and temperature drift.
Unlike the LTC2430, the LTC2435 and LTC2435-1 do not
perform an offset calibration every conversion cycle. This
enablestheLTC2435/LTC2435-1todoubletheiroutputrate
whilemaintaininglinefrequencyrejection.Theinitialoffset
of the LTC2435/LTC2435-1 is within 5mV independent of
VREF . Based on the LTC2435/LTC2435-1 new modulator
architecture, the temperature drift of the offset is less than
100nV/°C. More information on the LTC2435/LTC2435-1
offset is described in the Offset Accuracy and Drift section
of this data sheet.
Power-Up Sequence
The LTC2435/LTC2435-1 automatically enter an internal
reset state when the power supply voltage VCC drops
below approximately 2.2V. This feature guarantees the
integrity of the conversion result and of the serial interface
mode selection. (See the 2-wire I/O sections in the Serial
Interface Timing Modes section.)
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signalwithadurationofapproximately1ms.ThePORsignal
clears all internal registers. Following the POR signal, the
LTC2435/LTC2435-1 start a normal conversion cycle and
follow the succession of states described above. The first
conversion result following POR is accurate within the
specifications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
Reference Voltage Range
These converters accept a truly differential external
reference voltage. The absolute/common mode voltage
specification for the REF+ and REF– pins covers the entire
rangefromGNDtoVCC.Forcorrectconverteroperation,the
REF+ pin must always be more positive than the REF– pin.
TheLTC2435/LTC2435-1canacceptadifferentialreference
voltage from 0.1V to VCC. The converter output noise is
determined by the thermal noise of the front-end circuits,
and as such, its value is nearly constant with reference
voltage. A decrease in reference voltage will not signifi-
cantly improve the converter’s effective resolution. On the
other hand, a reduced reference voltage will improve the
converter’s overall INL performance. A reduced reference
voltage will also improve the converter performance when
operated with an external conversion clock (external FO
signal) at substantially higher output data rates (see the
Output Data Rate section).
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2435/LTC2435-1 convert the bipolar dif-
ferential input signal, VIN = IN+ – IN–, from –FS = –0.5
VREF to + FS = 0.5 VREF where VREF = REF+ – REF–.
Outside this range, the converters indicate the overrange
or the underrange condition using distinct output codes.
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the perfor-
mance of the device. In the physical layout, it is important
to maintain the parasitic capacitance of the connection
between these series resistors and the corresponding
pins as low as possible; therefore, the resistors should
be located as close as practical to the pins. The effect of
the series resistance on the converter accuracy can be
evaluated from the curves presented in the Input Current/
Reference Current sections. In addition, series resistors
will introduce a temperature dependent offset error due
to the input leakage current. A 1nA input leakage current
will develop a 1ppm offset error on a 5k resistor if VREF =
5V. This error has a very strong temperature dependency.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8611ARZ-REEL7 | IC COMP SGL 4NS ULTRFAST 8SOIC |
| AD7823YRZ | IC ADC 8BIT SRL 2.7/5.5V 8-SOIC |
| LTC1540IMS8#TRPBF | IC COMP NANOPOWER W/REF 8-MSOP |
| ISL4489EIBZ | TRANSCEIVER RS-485/422 14-SOIC |
| LTC1540IMS8#TR | IC COMP 300NA 2% VOLT REF 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2435-1IGN | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN#PBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2435-1IGN#TR | 功能描述:IC CONV A/D 20BIT DIFF 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2435-1IGN#TRPBF | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2435CGN | 功能描述:IC ADC DIFF I/REF 20BIT 16-SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
发布紧急采购，3分钟左右您将得到回复。