- 您现在的位置：买卖IC网 > PDF目录10688 > LTC2486IDE#PBF (Linear Technology)IC ADC 16BIT W/PGA 14-DFN PDF资料下载
参数资料
| 型号： | LTC2486IDE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/36页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT W/PGA 14-DFN |
| 标准包装： | 91 |
| 位数： | 16 |
| 采样率（每秒）： | 15 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 800µW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-DFN-EP（4x3） |
| 包装： | 管件 |
| 输入数目和类型： | 4 个单端，双极；2 个差分，双极 |
| 产品目录页面： | 1348 (CN2011-ZH PDF) |
| 配用： | DC1009A-C-ND - BOARD DELTA SIGMA ADC LTC2486 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC2486
11
2486fd
PIN FUNCTIONS
fO (Pin 1): Frequency Control Pin. Digital input that controls
the internal conversion clock rate. When fO is connected to
GND, the converter uses its internal oscillator running at
307.2kHz. The conversion clock may also be overridden by
driving the fO pin with an external clock in order to change
the output rate and the digital lter rejection null.
SDI (Pin 2): Serial Data Input. This pin is used to select
the gain, line frequency rejection mode, 1x or 2x speed
mode, temperature sensor, as well as the input channel.
The serial data input is applied under control of the serial
clock (SCK) during the data output/input operation. The
rst conversion following a new input or mode change
is valid.
SCK (Pin 3): Bidirectional, Digital I/O, Clock Pin. In Internal
Serial Clock Operation mode, SCK is generated internally
and is seen as an output on the SCK pin. In External Serial
Clock Operation mode, the digital I/O clock is externally
applied to the SCK pin. The Serial Clock operation mode
is determined by the logic level applied to the SCK pin at
power up and during the most recent falling edge of CS.
CS (Pin 4): Active LOW Chip Select. A LOW on this pin
enables the digital input/output and wakes up the ADC.
Following each conversion, the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the data output aborts the data transfer and starts
a new conversion.
SDO (Pin 5): Three-State Digital Output. During the data
output period, this pin is used as the serial data output.
When the chip select pin is HIGH, the SDO pin is in a high
impedance state. During the conversion and sleep periods,
this pin is used as the conversion status output. When
the conversion is in progress this pin is HIGH; once the
conversion is complete SDO goes low. The conversion
status is monitored by pulling CS LOW.
GND (Pin 6): Ground. Connect this pin to a common ground
plane through a low impedance connection.
COM (Pin 7): The common negative input (IN–) for all
single ended multiplexer congurations. The voltage on
CH0 to CH3 and COM pins can have any value between
GND – 0.3V to VCC + 0.3V. Within these limits, the two
selected inputs (IN+ and IN–) provide a bipolar input range
VIN = (IN+ – IN–) from –0.5 VREF/Gain to 0.5 VREF/Gain.
Outside this input range, the converter produces unique
over-range and under-range output codes.
CH0 to CH3 (Pins 8-11): Analog Inputs. May be pro-
grammed for single-ended or differential mode.
VCC (Pin 12): Positive Supply Voltage. Bypass to GND with
a 10μF tantalum capacitor in parallel with a 0.1μF ceramic
capacitor as close to the part as possible.
REF+ (Pin 13), REF– (Pin 14): Differential Reference
Input. The voltage on these pins can have any value
between GND and VCC as long as the reference positive
input, REF+, remains more positive than the negative
reference input, REF–, by at least 0.1V. The differential
voltage VREF = (REF+ – REF–) sets the full-scale range
(–0.5 VREF/Gain to 0.5 VREF/Gain) for all input channels.
When performing an on-chip temperature measurement,
the minimum value of REF = 2V.
Exposed Pad (Pin 15): Ground. This pin is ground and
must be soldered to the PCB ground plane. For prototyping
purposes, this pin may remain oating.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8561AR-REEL | IC COMP 7NS ULTRA-FAST 8-SOIC |
| HIN213EIBZ | IC 4DRVR/5RCVR RS232 5V 28-SOIC |
| LTC1444CDHD#PBF | IC COMP QD LP 1.221VREF 16-DFN |
| LTC1445CDHD#PBF | IC COMP QD LP 1.221VREF 16-DFN |
| LTC2487IDE#PBF | IC ADC 16BIT DELTA SIG 14-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2487CDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2487CDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2487IDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2487IDE#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2488CDE#PBF | 功能描述:IC ADC 16BIT DELTA SIG 14-DFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。