- 您现在的位置：买卖IC网 > PDF目录98002 > LTC3125EDCB#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1900 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | LTC3125EDCB#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1900 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 2 X 2 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, DFN-8 |
| 文件页数： | 17/18页 |
| 文件大小： | 303K |
| 代理商： | LTC3125EDCB#PBF |
LTC3125
8
3125fa
OPERATION
The LTC3125 provides high efciency, low noise power
for applications in portable instrumentation and those
with pulsed-load, power-limited requirements such as
GSM modems.
The LTC3125 directly and accurately controls the average
input current. The high efciency of the LTC3125 provides
the maximum possible output current to the load without
impacting the host. Together with an external bulk capaci-
tor the LTC3125 with average input current limit allows a
GSM/GPRS modem to be interfaced directly to a PCMCIA
or CompactFlash power bus without overloading it.
The current mode architecture with adaptive slope com-
pensation provides excellent transient load response,
requiring minimal output ltering. Internal soft-start and
loop compensation simplies the design process while
minimizing the number of external components.
With its low RDS(ON) and low gate charge internal N-chan-
nel MOSFET switch and P-channel MOSFET synchronous
rectier, the LTC3125 achieves high efciency over a wide
range of load currents. Automatic Burst Mode operation
maintains high efciency at very light loads, reducing the
quiescent current to just 15μA.
ERROR AMPLIFIER
The noninverting input of the transconductance error
amplier is internally connected to the 1.2V reference
and the inverting input is connected to FB. Clamps limit
the minimum and maximum error amp output voltage for
improved large-signal transient response. Power converter
control loop compensation is provided internally. An exter-
nal resistive voltage divider from VOUT to ground programs
the output voltage via FB from 2V to 5.25V.
VOUT =1.2V 1+
R2
R1
INTERNAL CURRENT LIMIT
Lossless current sensing converts the peak current signal of
the N-channel MOSFET switch into a voltage that is summed
with the internal slope compensation. The summed signal
is compared to the error amplier output to provide a peak
current control command for the PWM.
A second current limit comparator shuts off the N-chan-
nel MOSFET switch once the peak current signal clamp
threshold is reached. The current limit comparator delay
to output is typically 60ns. Peak switch current is limited
to approximately 1.8A, independent of input or output
voltage, unless VOUT falls below 0.8V, in which case the
current limit is cut in half.
AVERAGE INPUT CURRENT LIMIT
A current proportional to the internally sensed input current
is sourced out of the PROG pin. The voltage across the
external resistor on the PROG pin is averaged and com-
pared to a temperature stable internal reference, providing
a signal to actively control the current limit comparator’s
clamp threshold. The high gain of this loop forces the
average input current to the limit set by the value of the
external resistor, RPROG.
The LTC3125 is trimmed and tested at 500mA to obtain a
±5% initial accuracy. At other current limit settings, non-
idealities such as random offsets in the input current limit
loop will degrade the accuracy in the application. RPROG
tolerance must also be considered when setting the input
current limit as the accuracies listed in the Electrical Char-
acteristics section do not include external resistor variation.
Traditional, internally compensated, current mode con-
trolled boost converters can be unstable with the high
capacitance and low ESR values used in supercapacitor
chargers and pulsed load applications. The internal loop
compensation of the LTC3125 is optimized to be stable with
output capacitor values greater than 150μF with very low
ESR. Output capacitor values below 150μF will degrade
transient response and can lead to instability.
Note that the LTC3125’s input current averaging circuit
may introduce a slightly higher inductor current ripple
than expected. This is normal and has no affect on the
average input current seen by the power source.
ZERO CURRENT COMPARATOR
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous rectier
when this current reduces to approximately 30mA. This
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3406ES5-1.2#PBF | 1.3 A SWITCHING REGULATOR, 1800 kHz SWITCHING FREQ-MAX, PDSO5 |
| LTC3414MPFE#PBF | 9.5 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, PDSO20 |
| LTC3522EUD#TR | 0.85 A DUAL SWITCHING CONTROLLER, 1330 kHz SWITCHING FREQ-MAX, PQCC16 |
| LTC3525LESC6-3#PBF | 0.45 A SWITCHING REGULATOR, PDSO6 |
| LTC3526LEDC | SWITCHING CONTROLLER, 1250 kHz SWITCHING FREQ-MAX, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3125EDCBTRMPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Up 1.8-5.5V DFN8EP |
| LTC3125EDCB-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.2A Synchronous Step-Up DC/DC Converter with Input Current Limit |
| LTC3127 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:40V, 2A Synchronous Buck-Boost DC/DC Converter |
| LTC3127EDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A Buck-Boost DC/DC Converter with Programmable Input Current Limit |
| LTC3127EDD#PBF | 功能描述:IC BUCK BOOST SYNC ADJ 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:热电冷却器 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.173"，4.40mm 宽）裸露焊盘 供应商设备封装:28-TSSOP 裸露焊盘 包装:管件 产品目录页面:1410 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。