- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3407EDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 1A DL 10DFN PDF资料下载
参数资料
| 型号： | LTC3407EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1A DL 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.5MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LTC3407
OPERATION
V OUT ?
V OUT
? ?? 1–
V IN(MAX) ? ?
decrease causes the error ampli?er to increase the I TH
voltage until the average inductor current matches the
new load current.
The main control loop is shut down by pulling the RUN
pin to ground.
Low Current Operation
Two modes are available to control the operation of the
LTC3407 at low currents. Both modes automatically switch
from continuous operation to to the selected mode when
the load current is low.
To optimize ef?ciency, the Burst Mode operation can be
selected. When the load is relatively light, the LTC3407
automatically switches into Burst Mode operation in which
the PMOS switch operates intermittently based on load
demand with a ?xed peak inductor current. By running
cycles periodically, the switching losses which are domi-
nated by the gate charge losses of the power MOSFETs
are minimized. The main control loop is interrupted when
the output voltage reaches the desired regulated value.
A hysteretic voltage comparator trips when I TH is below
0.35V, shutting off the switch and reducing the power. The
output capacitor and the inductor supply the power to the
load until I TH exceeds 0.65V, turning on the switch and the
main control loop which starts another cycle.
APPLICATIONS INFORMATION
A general LTC3407 application circuit is shown in Figure 2.
External component selection is driven by the load require-
ment, and begins with the selection of the inductor L. Once
the inductor is chosen, C IN and C OUT can be selected.
Inductor Selection
Although the inductor does not in?uence the operat-
ing frequency, the inductor value has a direct effect on
ripple current. The inductor ripple current Δ I L decreases
with higher inductance and increases with higher V IN or
V OUT :
V ? V ?
Δ I L = OUT ? ? 1 ? OUT ?
f O ? L ? V IN ?
Accepting larger values of Δ I L allows the use of low
inductances, but results in higher output voltage ripple,
For lower ripple noise at low currents, the pulse-skipping
mode can be used. In this mode, the LTC3407 continues to
switch at a constant frequency down to very low currents,
where it will begin skipping pulses.
Dropout Operation
When the input supply voltage decreases toward the
output voltage, the duty cycle increases to 100% which
is the dropout condition. In dropout, the PMOS switch is
turned on continuously with the output voltage being equal
to the input voltage minus the voltage drops across the
internal P-channel MOSFET and the inductor.
An important design consideration is that the R DS(ON)
of the P-channel switch increases with decreasing input
supply voltage (See Typical Performance Characteristics).
Therefore, the user should calculate the power dissipation
when the LTC3407 is used at 100% duty cycle with low
input voltage (See Thermal Considerations in the Applica-
tions Information Section).
Low Supply Operation
The LTC3407 incorporates an Under-Voltage Lockout circuit
which shuts down the part when the input voltage drops
below about 1.65V to prevent unstable operation.
greater core losses, and lower output current capability. A
reasonable starting point for setting ripple current is Δ I L =
0.3 ? I LIM , where I LIM is the peak switch current limit. The
largest ripple current Δ I L occurs at the maximum input
voltage. To guarantee that the ripple current stays below a
speci?ed maximum, the inductor value should be chosen
according to the following equation:
?
L ≥ ?
f O ? Δ I L ?
The inductor value will also have an effect on Burst Mode
operation. The transition from low current operation
begins when the peak inductor current falls below a level
set by the burst clamp. Lower inductor values result in
higher ripple current which causes this to occur at lower
3407fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3408EDD#TRPBF | IC REG BUCK W/BYPASS TXRX 8-DFN |
| LTC3409IDD#TRPBF | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| LTC3410BESC6-1.8#TRPBF | IC REG BUCK SYNC 1.8V .3A SC70-6 |
| LTC3411AIMS#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
| LTC3411IMS#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3407EMSE | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407EMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407EMSE#TR | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407EMSE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3407EMSE-2 | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step Down 2.5V to 5.5V 10-Pin MSOP EP |
发布紧急采购，3分钟左右您将得到回复。