参数资料
| 型号： | LTC3417EDHC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ DL 16DFN |
| 标准包装： | 73 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.8 V ~ 5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.5MHz，600kHz ~ 4MHz |
| 电流 - 输出： | 800mA，1.4A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFDFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-DFN（5x3） |
LTC3417
APPLICATIONS INFORMATION
3) I 2 R losses are calculated from the DC resistances of the
internal switches, R SW , and the external inductor, R L . In
continuous mode, the average output current ?owing
through inductor L is “chopped” between the internal
top and bottom switches. Thus, the series resistance
looking into the SW pin is a function of both top and
bottom MOSFET R DS(ON) and the duty cycle (DC) as
follows:
R SW = (R DS(ON) TOP)(DC) + (R DS(ON) BOT)(1 – DC)
The R DS(ON) for both the top and bottom MOSFETs can be
obtained from the Typical Performance Characteristics
curves. Thus, to obtain I 2 R losses:
I 2 R losses = I OUT2 (R SW + R L )
where R L is the resistance of the inductor.
4) Other “hidden” losses such as copper trace and internal
battery resistances can account for additional ef?ciency
degradations in portable systems. It is very important
to include these “system” level losses in the design of a
system. The internal battery and fuse resistance losses
can be minimized by making sure that C IN has adequate
charge storage and very low ESR COUT at the switching
frequency. Other losses including diode conduction
losses during dead-time and inductor core losses gener-
ally account for less than 2% total additional loss.
Thermal Considerations
The LTC3417 requires the package Exposed Pad (PGND2/
GNDD pin) to be well soldered to the PC board. This gives
the DFN and TSSOP packages exceptional thermal proper-
ties, compared to similar packages of this size, making it
dif?cult in normal operation to exceed the maximum junc-
tion temperature of the part. In a majority of applications,
the LTC3417 does not dissipate much heat due to its high
ef?ciency. However, in applications where the LTC3417 is
running at high ambient temperature with low supply volt-
age and high duty cycles, such as in dropout, the heat dis-
sipated may exceed the maximum junction temperature of
the part. If the junction temperature reaches approximately
150°C, both switches in both regulators will be turned off
and the SW nodes will become high impedance.
To prevent the LTC3417 from exceeding its maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum
junction temperature of the part. The temperature rise is
given by:
T RISE = P D ? θ JA
where P D is the power dissipated by the regulator and θ JA
is the thermal resistance from the junction of the die to
the ambient temperature.
The junction temperature, T J , is given by:
T J = T RISE + T AMBIENT
As an example, consider the case when the LTC3417 is
in dropout in both regulators at an input voltage of 3.3V
with load currents of 1.4A and 800mA. From the Typical
Performance Characteristics graph of Switch Resistance,
the R DS(ON) resistance of the 1.4A P-channel switch is
0.09Ω and the R DS(ON) of the 800mA P-channel switch
is 0.163Ω. The power dissipated by the part is:
PD = I 12 ? R DS(ON)1 + I 22 ? R DS(ON)2
PD = 1.4 2 ? 0.09 + 0.8 2 ? 0.163
PD = 281mW
The DFN package junction-to-ambient thermal resistance,
θ JA , is about 43°C/W. Therefore, the junction temperature
of the regulator operating in a 70°C ambient temperature
is approximately:
T J = 0.281 ? 43 + 70
T J = 82.1°C
Remembering that the above junction temperature is
obtained from an R DS(ON) at 25°C, we might recalculate
the junction temperature based on a higher R DS(ON) since
it increases with temperature. However, we can safely as-
sume that the actual junction temperature will not exceed
the absolute maximum junction temperature of 125°C.
3417fd
15
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3418EUHF#TRPBF | IC REG BUCK SYNC ADJ 8A 38QFN |
| LTC3419IMS-1#TRPBF | IC REG BUCK SYNC ADJ 0.6A 10MSOP |
| LTC3421EUF#TRPBF | IC REG BOOST SYNC ADJ 1.5A 24QFN |
| LTC3422EDD#TRPBF | IC REG BOOST SYNC ADJ 1.5A 10DFN |
| LTC3424EMS#TR | IC REG BOOST SYNC ADJ 2A 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3417EFE | 制造商:Linear Technology 功能描述:Conv DC-DC Dual Step Down 2.25V to 5.5V 20-Pin TSSOP EP |
| LTC3417EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3417EFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ DL 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3418 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:24V, 15A Monolithic Step Down Regulator with Differential Output Sensing |
| LTC3418EUHF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.25V to 5.5V 38-Pin QFN EP |
发布紧急采购，3分钟左右您将得到回复。