- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3522EUD#TRPBF (Linear Technology)IC REG BUCK BOOST SYNC ADJ 16QFN PDF资料下载
参数资料
| 型号： | LTC3522EUD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 16QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.4 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1.07MHz |
| 电流 - 输出： | 200mA，400mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-QFN-EP（3x3） |
LTC3522
OPERATION
LTC3522
V OUT1
V OUT
current limit will have a dependency on the duty cycle
(i.e., on the input and output voltages in the overcurrent
condition).
+
–
1V
FB1
R2
The speed of the average current limit circuit is limited by
the dynamics of the error ampli?er. On a hard output short,
R1
GND
3522 F02
Figure 2. Buck-Boost Error Ampli?er and Compensation
it would be possible for the inductor current to increase
substantially beyond current limit before the average cur-
rent limit circuit would react. For this reason, there is a
second current limit circuit which turns off switch A if the
current ever exceeds approximately 165% of the average
current limit value. This provides additional protection in
the case of an instantaneous hard output short.
response of the compensation network. The ratio of R2 to
R1 must be set to program the desired output voltage but
this still allows the value of R2 to be adjusted to optimize
the transient response of the converter. Increasing the value
of R2 generally leads to greater stability at the expense of
reduced transient response speed. Increasing the value of
R2 can yield substantial transient response improvement in
cases where the phase margin has been reduced due to the
use of a small value output capacitor or a large inductance
(particularly with large boost step-up ratios). Conversely,
decreasing the value of R2 increases the loop bandwidth
which can improve the speed of the converter’s transient
response. This can be useful in improving the transient
response if a large valued output capacitor is utilized. In
this case, the increased bandwidth created by decreasing
R2 is used to counteract the reduced converter bandwidth
caused by the large output capacitor.
Current Limit Operation
Reverse Current Limit
The reverse current comparator on switch D monitors
the inductor current entering V OUT1 . When this current
exceeds 250mA (typical) switch D will be turned off for
the remainder of the switching cycle.
Burst Mode Operation
With the PWM pin held low, the buck-boost converter
operates utilizing a variable frequency switching algorithm
designed to improve ef?ciency at light load and reduce
the standby current at zero load. In Burst Mode operation,
the inductor is charged with ?xed peak amplitude current
pulses. These current pulses are repeated as often as
necessary to maintain the output regulation voltage. The
typical output current which can be supplied in Burst Mode
operaton is dependent upon the input and output voltage
as given by the following formula:
The buck-boost converter has two current limit circuits.
The primary current limit is an average current limit circuit
I OUT ( MAX ), BURST =
0 . 11 ? V IN
V IN + V OUT
( A )
which injects an amount of current into the feedback node
which is proportional to the extent that the switch A cur-
rent exceeds the current limit value. Due to the high gain
of this loop, the injected current forces the error ampli?er
output to decrease until the average current through switch
A decreases approximately to the current limit value. The
average current limit utilizes the error ampli?er in an ac-
tive state and thereby provides a smooth recovery with
little overshoot once the current limit fault condition is
removed. Since the current limit is based on the average
current through switch A, the peak inductor current in
In Burst Mode operation, the error ampli?er is not used but
is instead placed in a low current standby mode to reduce
supply current and improve light load ef?ciency.
Soft-Start
The buck-boost converter has an internal voltage mode
soft-start circuit with a nominal duration of 600μs. The
converter remains in regulation during soft-start and will
therefore respond to output load transients that occur
during this time. In addition, the output voltage rise time
3522fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3523EUD-2#TRPBF | IC REG BUCK BOOST SYNC ADJ 16QFN |
| LTC3525ESC6-3.3#TRPBF | IC REG BST SYNC 3.3V 0.4A SC70-6 |
| LTC3526BEDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| LTC3527EUD-1#TRPBF | IC REG BOOST SYNC ADJ DL 16QFN |
| LTC3528EDDB#TRPBF | IC REG BOOST SYNC ADJ 1A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3523 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 600mA Step-Up and 400mA Step-Down DC/DC Converters |
| LTC3523EUD#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3523EUD#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3523EUD-2#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3523EUD-2#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。