- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3534EGN#TRPBF (Linear Technology)IC REG BUCK BST SYNC 0.5A 16SSOP PDF资料下载
参数资料
| 型号： | LTC3534EGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST SYNC 0.5A 16SSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.8 V ~ 7 V |
| 输入电压： | 2.4 V ~ 7 V |
| PWM 型： | Burst Mode? |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-SSOP |
LTC3534
OPERATION
V IN(ENTER4SW) ?
V OUT
shiftedvoltagefromtheoutputoftheerroramplifier(V C
pin), see Figure 3. The four power switches are properly
phased so the transfer between operating modes is con-
tinuous, smooth and transparent to the user. When V IN
approaches V OUT the buck-boost region is entered, where
the conduction time of the four switch region is typically
125ns. Referring to Figures 1 and 2, the various regions
of operation will now be described.
Buck Region (V IN > V OUT )
Switch D is always on and switch C is always off during
this mode. When the internal control voltage, V CI , is above
voltage V1, output A begins to switch. During the off-
time of switch A, synchronous switch B turns on for the
remainder of the period. Switches A and B will alternate
similar to a typical synchronous buck regulator. As the
control voltage increases, the duty cycle of switch A
increases until the maximum duty cycle of the converter
in buck mode reaches D MAX_BUCK , given by:
D MAX_BUCK = (100 – D4 SW )%
where D4 SW = duty cycle % of the four switch range.
D4 SW = (125ns ? f) ? 100%
where f = operating frequency in Hz, typically 1MHz.
Hence, D4 SW = 12.5% for the LTC3534.
D MAX_BUCK = 87.5%
Beyond this point the “four switch”, or buck-boost region
is reached.
Buck-Boost or Four Switch (V IN ~ V OUT )
When the internal control voltage, V CI , is above voltage V2,
switch pair AD remain on for duty cycle D MAX_BUCK , and
the switch pair AC begins to phase in. As switch pair AC
phases in, switch pair BD phases out accordingly. When
V CI reaches the edge of the buck-boost range, at voltage
V3, the AC switch pair completely phase out the BD pair,
and the boost phase begins at duty cycle D4 SW .
The input voltage, V IN , where the four switch region begins
is given by:
The V IN potential at which the four switch region ends is
given by:
V IN = V OUT ? (1 – D) = V OUT ? (1 – 125ns ? ?) V
where f = operating frequency in Hz, typically 1MHz.
Hence, for the LTC3534,
V
0.875
Approximate V IN potential at which the four switch
region is entered.
V IN(4SWEXIT) @ 0.875 ? V OUT V
Approximate V IN potential at which the four switch
region is exited.
Boost Region (V IN < V OUT )
Switch A is always on and switch B is always off during
this mode. When the internal control voltage, V CI , is above
voltage V3, switch pair CD will alternately switch to provide
a boosted output voltage. This operation is typical to a
synchronous boost regulator. The maximum duty cycle
of the converter is limited to 85% typical and is reached
when V CI is above V4.
Burst Mode OPERATION
Burst Mode operation reduces the LTC3534’s quiescent
current consumption at light loads and improves overall
conversion efficiency, increasing battery life. During Burst
Mode operation the LTC3534 delivers energy to the output
until it is regulated and then enters a sleep state where
the switches are off and the quiescent current drops to
25μA typical. In this mode the output ripple has a variable
frequency component that depends upon load current,
and will typically be about 2% peak-to-peak. Burst Mode
operation ripple can be reduced slightly by using more
output capacitance (47μF or greater). Another method of
reducing Burst Mode operation ripple is to place a small
feedforward capacitor across the upper resistor in the
V OUT feedback divider network (as in Type III compensa-
tion), see Figure 6.
V IN =
10
V OUT
1 ? ( 125ns ? f )
V
For more information www.linear.com/LTC3534
3534fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3535EDD#PBF | IC REG BST SYNC ADJ 0.55A 12DFN |
| LTC3536IMSE#TRPBF | IC REG BUCK BST SYNC ADJ 12MSOP |
| LTC3538EDCB#TRPBF | IC REG BUCK BOOST SYNC ADJ 8DFN |
| LTC3539EDCB-2#TRPBF | IC REG BOOST SYNC ADJ 2A 8DFN |
| LTC3542IDC#TRMPBF | IC REG BUCK SYNC ADJ 0.5A 6DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3535 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Channel 550mA 1MHz Synchronous Step-Up DC/DC Converter |
| LTC3535EDD#PBF | 功能描述:IC REG BST SYNC ADJ 0.55A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3535EDD#PBF | 制造商:Linear Technology 功能描述:DC/DC CONVERTER IC |
| LTC3535EDD#TRPBF | 功能描述:IC REG BST SYNC ADJ 0.55A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3535EDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Channel 550mA 1MHz Synchronous Step-Up DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。