- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3589HUJ-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 PDF资料下载
参数资料
| 型号： | LTC3589HUJ-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封装： | 6 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 14/46页 |
| 文件大小： | 570K |
| 代理商： | LTC3589HUJ-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
LTC3589/LTC3589-1
21
3589fc
Table 5. Step-Down Switching Regulator 1 Command Register
Settings
COMMAND
REGISTER[BIT]
VALUE
SETTING
SCR1[1-0]
00*
01
10
Pulse-Skipping Mode
Burst Mode Operation
Forced Continuous Mode
OVEN[0]
0*
1
Disable
Enable
SCR2[0]
0*
1
Wait for Output Below 300mV Before Enable
Enable Immediately
VCCR[1]
0*
1
Select Register B1DTV1 (V1) Reference
Select Register B1DTV2 (V2) Reference
VCCR[0]
1
Initiate Dynamic Voltage Slew
VRRCR[1-0]
00
01
10
11*
Reference Slew Rate = 0.88mV/μs
Reference Slew Rate = 1.75mV/μs
Reference Slew Rate = 3.5mV/μs
Reference Slew Rate = 7mV/μs
B1DTV1[5]
0*
1
Force PGOOD Low When Slewing
Normal PGOOD Operation When Slewing
B1DTV1[4-0]
11001*
DAC Dynamic Target Voltage V1
B1DTV2[4-0]
11001*
DAC Dynamic Target Voltage V2
B1DTV2[5]
0*
1
2.25MHz Switching Frequency
1.125MHz Switching Frequency
B1DTV2[6]
0*
1
Switch on Clock Phase 1
Switch on Clock Phase 2
B1DTV2[7]
0*
1
Shutdown Regulator 1 Normally
Keep Regulator 1 Alive
* Denotes Default Power-On Value
Soft-Start
Soft-start is accomplished by gradually increasing the
input reference voltage on each step-down switching
regulator from 0V to the dynamic reference DAC output
level at a rate of 0.8V/ms. This allows each output to
rise slowly, helping minimize inrush current required to
charge up the regulator output capacitor. A soft-start cycle
occurs whenever a regulator is enabled either initially or
while powering up following a fault condition. A soft-start
cycle is not triggered by a change of operating modes or
a dynamic voltage slew. During soft-start the converter is
forced to pulse-skipping mode regardless of the settings
in the SCR1 command register.
OPERATION
Table 6. Step-Down Switching Regulator 2 Command Register
Settings
COMMAND
REGISTER[BIT]
VALUE
SETTING
SCR1[3-2]
00*
01
10
Pulse-Skipping Mode
Burst Mode Operation
Forced Continuous Mode
OVEN[1]
0*
1
Disable
Enable
SCR2[1]
0*
1
Wait for Output Below 300mV Before Enable
Enable immediately
VCCR[3]
0*
1
Select Register B2DTV1 (V1) Reference
Select Register B2DTV2 (V2) Reference
VCCR[2]
1
Initiate Dynamic Voltage Slew
VRRCR[3-2]
00
01
10
11*
Reference Slew Rate = 0.88mV/μs
Reference Slew Rate = 1.75mV/μs
Reference Slew Rate = 3.5mV/μs
Reference Slew Rate = 7mV/μs
B2DTV1[5]
0*
1
Force PGOOD Low When Slewing
Normal PGOOD Operation When Slewing
B2DTV1[4-0]
11001*
DAC Dynamic Target Voltage V1
B2DTV2[4-0]
11001*
DAC Dynamic Target Voltage V2
B2DTV2[5]
0*
1
2.25MHz Switching Frequency
1.125MHz Switching Frequency
B2DTV2[6]
0*
1
Switch on Clock Phase 1
Switch on Clock Phase 2
B2DTV2[7]
0*
1
Shutdown Regulator 2 Normally
Keep Regulator 2 Alive
* Denotes Default Power-On Value
Switching EMI Control
The step-down switching regulators contain new pat-
ent pending circuitry to limit the edge rate of the switch
nodes SW1, SW2, and SW3. This new circuitry controls
the transition of the switch node over a period of a few
nanoseconds, signicantly reducing radiated EMI and
conducted supply noise while maintaining high efciency.
Since slowing the slew rate of the switch nodes causes
efciency loss, the slew rate of the step-down switching
regulators is adjustable using the I2C command register
B1DTV1 bits 6 and 7. Optimize efciency or EMI as neces-
sary with four different slew rate settings. The power-on
default is the fastest slew rate, highest efciency setting.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3589EUJ#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3589IUJ-1#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3609IWKG#PBF | SWITCHING REGULATOR, PQCC52 |
| LTC3609IWKG#TRPBF | SWITCHING REGULATOR, PQCC52 |
| LTC3614IUDD#PBF | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3589HUJ-2#PBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-2#TRPBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589HUJ-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589IUJ#PBF | 功能描述:IC DC/DC CONV 8-OUTPUT 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。