- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3589HUJ-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 PDF资料下载
参数资料
| 型号： | LTC3589HUJ-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封装： | 6 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 22/46页 |
| 文件大小： | 570K |
| 代理商： | LTC3589HUJ-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
LTC3589/LTC3589-1
29
3589fc
Figure 5. Pushbutton Controller State Diagram
1 SEC
POR
5 SEC
LTC3589
LTC3589-1
PB400ms OR
PWR_ON
FAULT OR
PWR_ON
PUP
PON
POFF
PDN
1 SEC
POR
3589 F05
5 SEC
PB400ms OR
PWR_ON
FAULT OR
PWR_ON
PUP
PON
POFF
PDN
seconds, and 3) a fault condition is detected. Fault condi-
tions are low VIN, device over temperature, or extended
undervoltage of one of the regulator outputs. All regulator
enables, the ON input, and PWR_ON signals are inhibited
for one second while in the PDN state. After one second
in PDN the pushbutton controller returns to POFF.
OPERATION
PBSTAT Operation
PBSTAT goes LOW 50ms after the initial pushbutton ap-
plication (ON LOW) and will stay LOW for a minimum of
50ms. PBSTAT will go HIGH coincident with ON going HIGH
unless ON goes HIGH before the 50ms minimum on-time.
Power-Up Using the Pushbutton
When in the POFF state, the LTC3589/LTC3589-1 is in
complete shutdown except the always active LDO1 and
regulators enabled with the keep-alive control bits. Pull the
ON pin to ground with a pushbutton for 400ms to begin a
power-up sequence with the WAKE pin tied to an enable
pin. Drive PWR_ON high within five seconds to signal
the LTC3589/LTC3589-1 to remain in the power-on state.
Power-Down Using the Pushbutton
The pushbutton power-down operation is performed by
the system microprocessor by monitoring the PBSTAT pin.
Once in the PON state, the system controller is responsible
for deciding what action to take with a pushbutton event.
When the ON pin is held LOW for a 50ms debounce period,
the PBSTAT pin is pulled LOW. The system controller should
monitor the PBSTAT pin to determine the pushbutton has
been pushed. If the controller decides that a power-down
is desired, then it should drive the PWR_ON pin LOW.
Power-Up and Down Using PWR_ON Pin
An alternate power-up method is to drive the PWR_ON pin
to a HIGH state. After a delay of 50ms from the PWR_ON
signal, the WAKE pin will pull HIGH to drive regulator en-
able pins. When PWR_ON is HIGH for five seconds, the
sequence controller will enter the PON state. To power
down, drive the PWR_ON pin LOW. 50ms later WAKE will
pull low, all enabled regulators are disabled and the OVEN
command register is reset to 0x00.
Hard Reset Using the Pushbutton
When the ON pin is pulled LOW for five seconds, a hard
reset is initiated. At the end of five seconds, WAKE is pulled
LOW, the I2C command registers are reset to POR states,
enable pin states are ignored, and the one second power-
down timer is started. During the power-down time, the
enablescontinuetobeignoredtoallowtheregulatoroutputs
to discharge. The RSTO pin is pulled LOW for the power-
down time to indicate a pushbutton hard reset occurred.
If the PWR_ON pin is LOW at the end of the one second
power-down time, the LTC3589/LTC3589-1 will remain in
sleep mode. If PWR_ON is HIGH at the end of one second
and there are no fault conditions, the LTC3589/LTC3589-1
will power-up in the same way shown in Figure 8.
Hard Reset Due to a Fault Condition
A hard reset due to VIN undervoltage, extended undervolt-
age of an output rail, or an overtemperature condition
initiates a hard shutdown of the LTC3589/LTC3589-1. When
the fault occurs, wake is pulled LOW, the I2C command
registers are reset to POR states, enable pin inputs are
ignored, and the one second power-down timer is started.
During the power-down time, the enables continue to be
ignored to allow the regulator outputs to discharge. If the
PWR_ON pin is LOW at the end of the power-down time,
the LTC3589/LTC3589-1 will remain in sleep mode with just
the always-active LDO operating. If PWR_ON is HIGH at
the end of one second and the fault condition has cleared,
the LTC3589/LTC3589-1 will power-up in the same way
shown in Figure 8. Neither IRQ nor the status registers
are cleared by the fault induced shutdown.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3589EUJ#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3589IUJ-1#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3609IWKG#PBF | SWITCHING REGULATOR, PQCC52 |
| LTC3609IWKG#TRPBF | SWITCHING REGULATOR, PQCC52 |
| LTC3614IUDD#PBF | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3589HUJ-2#PBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-2#TRPBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589HUJ-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589IUJ#PBF | 功能描述:IC DC/DC CONV 8-OUTPUT 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。