- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3589HUJ-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 PDF资料下载
参数资料
| 型号： | LTC3589HUJ-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封装： | 6 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 6/46页 |
| 文件大小： | 570K |
| 代理商： | LTC3589HUJ-1#PBF |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
LTC3589/LTC3589-1
14
3589fc
PIN FUNCTIONS
ON (Pin 21): Pushbutton Input. A weak internal pull-up
forces ON high when left oating. A normally open push-
button is connected from ON to ground to force a low
state on this pin.
PBSTAT (Pin 22): Pushbutton Status. Open-drain output
to be used for processor interrupts. PBSTAT mirrors the
status of ON pushbutton pin. PBSTAT is delayed 50ms
from ON pin for debounce.
WAKE (Pin 23): System Wake Up. Open-drain driver output
releases high when signaled by pushbutton activation or
PWR_ON input. It may be used to initiate a pin-strapped
power-up sequence by connecting to a regulator enable
pin to initiate a pin-strapped power-on sequence.
PVIN2 (Pin 24): Power Input for Step-Down Switching
Regulator 2. Tie this pin to VIN supply. This pin should
be bypassed to ground with a 4.7μF or greater ceramic
capacitor.
SW2 (Pin 25): Switch Pin for Step-Down Switching Regula-
tor 2. Connect one side of step-down switching regulator
2 inductor to this pin.
SW3 (Pin 26): Switch Pin for Step-Down Switching Regula-
tor 3. Connect one side of step-down switching regulator
3 inductor to this pin.
PVIN3 (Pin 27): Power Input for Step-Down Switching
Regulator 3. Tie this pin to the VIN supply. This pin should
be bypassed to ground with a 4.7μF or greater ceramic
capacitor.
VSTB (Pin 28): Voltage Standby. When VSTB is low, DAC
reference registers are selected by bit values in command
register VCCR. When VSTB is high, the DAC registers are
forced xxDVT2 registers. Tie VSTB to ground if unused.
PGOOD (Pin 29): Power Good Output. Open-drain output
pulls down when any regulator falls below power good
threshold and during regulator dynamic voltage slew
unless disabled in I2C register. Pulls down when all regula-
tors are disabled.
SCL (Pin 30): Clock Input Pin for the I2C Serial Port. The
I2C logic levels are scaled with respect to DVDD.
SDA (Pin 31): Data Input Pin for the I2C Serial Port. The
I2C logic levels are scaled with respect to DVDD.
DVDD (Pin 32): Supply Voltage for I2C Serial Port. This
pin sets the logic reference level of SCL and SDA I2C pins.
DVDD resets I2C registers to power on state when driven
to <1V. SCL and SDA logic levels are scaled to DVDD. Con-
nect a 0.1μF decoupling capacitor from this pin to ground.
BUCK2_FB (Pin 33): Feedback Input for Step-Down
Switching Regulator 2. Set full-scale output voltage using
resistor divider connected from the output of step-down
switching regulator 2 to this pin to ground.
BUCK3_FB (Pin 34): Feedback Input for Step-Down
Switching Regulator 3. Set full-scale output voltage using
resistor divider connected from the output of step-down
switching regulator 3 to this pin to ground.
LDO1_FB (Pin 35): Feedback Input for LDO1. Set out-
put voltage using a resistor divider connected from
LDO1_STDBY to this pin to ground.
LDO1_STDBY (Pin 36): Always-On LDO1 Output. This pin
provides an always-on supply voltage useful for light loads
such as a watchdog microprocessor or a real-time clock.
Connect a 1μF capacitor from LDO1_STBY to ground.
VIN (Pin 37): Supply Voltage Input. This pin should
be bypassed to ground with a 1μF or greater ceramic
capacitor.
LDO2_FB (Pin 38): Feedback Input for LDO2. Set full-scale
output voltage using a resistor divider connected from
LDO2_OUT to this pin to ground.
BUCK1_FB (Pin 39): Feedback Input for Step-Down
Switching Regulator 1. Set full-scale output voltage using
resistor divider connected from the output of step-down
switching regulator 1 to this pin to ground.
BB_FB (Pin 40): Feedback Input for Buck-Boost Switching
Regulator 4. Set the output voltage using resistor divider
connected from BB_OUT to this pin to ground.
GND (Exposed Pad Pin 41): Ground. The Exposed Pad must
be connected to a continuous ground plane on the second
layer of the printed circuit board by several interconnect
vias directly under the LTC3589 for maximum heat transfer.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3589EUJ#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3589IUJ-1#TRPBF | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| LTC3609IWKG#PBF | SWITCHING REGULATOR, PQCC52 |
| LTC3609IWKG#TRPBF | SWITCHING REGULATOR, PQCC52 |
| LTC3614IUDD#PBF | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3589HUJ-2#PBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-2#TRPBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589HUJ-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589HUJ-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589IUJ#PBF | 功能描述:IC DC/DC CONV 8-OUTPUT 40QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
发布紧急采购，3分钟左右您将得到回复。