- 您现在的位置：买卖IC网 > PDF目录13814 > LTC3613IWKH#PBF (Linear Technology)IC REG BUCK SYNC ADJ 15A 56QFN PDF资料下载
参数资料
| 型号： | LTC3613IWKH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 15A 56QFN |
| 标准包装： | 40 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 4.5 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 1MHz |
| 电流 - 输出： | 15A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-VFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 56-QFN 多焊盘（7x9） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3613
APPLICATIONS INFORMATION
The inductor DCR is sensed by connecting an RC filter
across the inductor. This filter typically consists of one
or two resistors (R1 and R2) and one capacitor (C1) as
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
shown in Figure 4. If the external R1||R2 ? C1 time constant
is chosen to be exactly equal to the L/DCR time constant,
the voltage drop across the external capacitor is equal
to the voltage drop across the inductor DCR multiplied
P LOSS ( R1 ) =
( V IN(MAX) –V OUT ) ? V OUT
R1
by R2/(R1 + R2). Therefore, R2 may be used to scale
the voltage across the sense terminals when the DCR is
greater than the target sense resistance. With the ability
to program current limit through the V RNG pin, R2 may
be optional. C1 is usually selected to be in the range of
0.01μF to 0.47μF. This forces R1|| R2 to around 2k to 4k,
reducing error that might have been caused by the sense
pins’ input bias currents.
The first step in designing DCR current sensing is to
determine the DCR of the inductor. Where provided, use
the manufacturer’s maximum value, usually given at 25°C.
Increase this value to account for the temperature coef-
ficient of resistance, which is approximately 0.4%/°C. A
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
R SENSE sensing. Light load power loss can be modestly
higher with a DCR network than with a sense resistor due
to the extra switching losses incurred through R1. However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher efficiency at heavy loads.
Peak efficiency is about the same with either method.
To maintain a good signal-to-noise ratio for the current
sense signal, use a minimum Δ V SENSE of 10mV. For a
DCR sensing application, the actual ripple voltage will be
determined by:
? OUT
conservative value for inductor temperature T L is 100°C.
The DCR of the inductor can also be measured using a good
RLC meter, but the DCR tolerance is not always the same
Δ V SENSE =
V IN –V OUT
R1 ? C1
V
V IN ? f
and varies with temperature; consult the manufacturers’
datasheets for detailed information.
From the DCR value, V SENSE(MAX) is calculated as:
? ?
V SENSE(MAX) =DCR MAX at 25°C ? ? 1+0.4% ( T L(MAX) –25°C ) ?
? ?? I OUT(MAX) – Δ I L /2 ??
If V SENSE(MAX) is within the maximum sense voltage of
the LTC3613 as programmed by the V RNG pin (30mV to
100mV), then the RC filter only needs R1. If V SENSE(MAX) is
higher, then R2 may be used to scale down the maximum
sense voltage so that it falls within range.
Operating Multiple Units in Parallel
The LTC3613’s current mode control architecture makes
it straightforward to parallel multiple units for higher
output current. Figure 13 shows an example circuit of two
LTC3613s placed in parallel to provide 30A at 1.2V from
a 6V to 24V input. The signals at MODE/PLLIN are 180°
out of phase, to reduce stress on the input and output
capacitors.
Since the ITH pin voltage determines the cycle-by-cycle
valley inductor current, sharing is achieved by connecting
the ITH pins together. Because the ITH pin is sensitive to
noise, a small 22pF to 47pF decoupling capacitor should
3613fa
17
相关PDF资料 |
PDF描述 |
|---|---|
| 35PX220MEFCT78X11.5 | CAP ALUM 220UF 35V 20% RADIAL |
| 35PX220MEFCTA8X11.5 | CAP ALUM 220UF 35V 20% RADIAL |
| UVR1C471MPD1TD | CAP ALUM 470UF 16V 20% RADIAL |
| 10ML470MEFCT78X9 | CAP ALUM 470UF 10V 20% RADIAL |
| 10ML470MEFCTA8X9 | CAP ALUM 470UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3614EUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3614EUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3614IUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3614IUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3614MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN |
发布紧急采购，3分钟左右您将得到回复。