- 您现在的位置：买卖IC网 > PDF目录15296 > LTC3713EG (Linear Technology)IC REG CTRLR BUCK PWM CM 24-SSOP PDF资料下载
参数资料
| 型号： | LTC3713EG |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-SSOP |
| 标准包装： | 59 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 90% |
| 电源电压： | 1.5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
LTC3713
APPLICATIO S I FOR ATIO
? I L = ? OUT ? ? 1 ? OUT ?
specificapplication.Agoodstartingpointistofeedabout
25% of the voltage change at the I TH pin to the V ON pin as
shown in Figure 4a. Place capacitance on the V ON pin to
filter out the I TH variations at the switching frequency. The
resistor load on I TH reduces the DC gain of the error amp
and degrades load regulation, which can be avoided by
using the PNP emitter follower of Figure 4b.
Inductor L1 Selection
Given the desired input and output voltages, the inductor
value and operating frequency determine the ripple
current:
? V ? ? V ?
? fL ? ? V IN ?
of the bottom MOSFET from turning on and storing charge
during the dead time, which can cause a modest (about
1%) efficiency loss. The diode can be rated for about one
half to one fifth of the full load current since it is on for only
a fraction of the duty cycle. In order for the diode to be
effective, the inductance between it and the bottom MOSFET
must be as small as possible, mandating that these
components be placed adjacently. The diode can be omit-
ted if the efficiency loss is tolerable.
C IN and C OUT Selection
The input capacitance C IN is required to filter the square
wave current at the drain of the top MOSFET. Use a low
ESR capacitor sized to handle the maximum RMS current.
Lower ripple current reduces cores losses in the inductor,
ESR losses in the output capacitors and output voltage
I RMS ? I OUT ( MAX )
V OUT
V IN
V IN
V OUT
–1
? ? ? V OUT ?
L = ?
? ? 1 ?
?
? V OUT ≤ ? I L ? ESR + ?
ripple. Highest efficiency operation is obtained at low
frequency with small ripple current. However, achieving
this requires a large inductor. There is a tradeoff between
component size, efficiency and operating frequency.
A reasonable starting point is to choose a ripple current
that is about 40% of I OUT(MAX) . The largest ripple current
occurs at the highest V IN . To guarantee that ripple current
does not exceed a specified maximum, the inductance
should be chosen according to:
V OUT
? f ? I L ( MAX ) ? ? V IN ( MAX ) ?
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron
cores, forcing the use of more expensive ferrite,
molypermalloy or Kool M μ ? cores. A variety of inductors
designed for high current, low voltage applications are
available from manufacturers such as Sumida, Panasonic,
Coiltronics, Coilcraft and Toko.
Schottky Diode D1 Selection
The Schottky diode D1 shown in Figure 1 conducts during
the dead time between the conduction of the power
MOSFET switches. It is intended to prevent the body diode
This formula has a maximum at V IN = 2V OUT , where
I RMS = I OUT(MAX) / 2. This simple worst-case condition is
commonly used for design because even significant
deviations do not offer much relief. Note that ripple
current ratings from capacitor manufacturers are often
based on only 2000 hours of life which makes it advisable
to derate the capacitor.
The selection of C OUT is primarily determined by the ESR
required to minimize voltage ripple and load step
transients. The output ripple ? V OUT is approximately
bounded by:
? 1 ?
? 8 fC OUT ?
Since ? I L increases with input voltage, the output ripple is
highest at maximum input voltage. Typically, once the ESR
requirement is satisfied, the capacitance is adequate for
filtering and has the necessary RMS current rating.
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount
packages. Special polymer capacitors offer very low ESR
but have lower capacitance density than other types.
Kool M μ is a registered trademark of Magnetics, Inc.
3713fa
13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-27P-EW-F3 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27P-EW-F2 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27P-EW-F1 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27N-EY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
| VE-27N-EW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3713EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3713EG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3713EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3714EG | 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3714EG#PBF | 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。