- 您现在的位置：买卖IC网 > PDF目录15296 > LTC3713EG (Linear Technology)IC REG CTRLR BUCK PWM CM 24-SSOP PDF资料下载
参数资料
| 型号： | LTC3713EG |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-SSOP |
| 标准包装： | 59 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 90% |
| 电源电压： | 1.5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
LTC3713
PI FU CTIO S
RUN/SS (Pin 1): Run Control and Soft-Start Input. A
capacitor to ground at this pin sets the ramp time to full
output current (approximately 3s/ μ F) and the time delay
for overcurrent latchoff (see Applications Information).
Forcing this pin below 0.8V shuts down the device.
V ON (Pin 2): On-Time Voltage Input. Voltage trip point for
the on-time comparator. Tying this pin to the output
voltage makes the on-time proportional to V OUT . The
comparator input defaults to 0.7V when the pin is grounded,
2.4V when the pin is tied to INTV CC .
PGOOD (Pin 3): Power Good Output. Open-drain logic
output that is pulled to ground when the output voltage is
not within ± 7.5% of the regulation point.
V RNG (Pin 4): Sense Voltage Range Input. The voltage at
this pin is ten times the nominal sense voltage at maxi-
mum output current and can be set from 0.5V to 2V by a
resistive divider from INTV CC . The nominal sense voltage
defaults to 70mV when this pin is tied to ground, 140mV
when tied to INTV CC .
FCB (Pin 5): Forced Continuous Input. Tie this pin to
ground to force continuous synchronous operation at low
load, to INTV CC to enable discontinuous mode operation
at low load or to a resistive divider from a secondary output
when using a secondary winding.
I TH (Pin 6): Current Control Threshold and Error Amplifier
Compensation Point. The current comparator threshold
increases with this control voltage. The voltage ranges
from 0V to 2.4V with 0.8V corresponding to zero sense
voltage (zero current).
SGND (Pins 7, 11): Signal Ground. All small-signal com-
ponents and compensation components should connect to
this ground, which in turn connects to PGND at one point.
I ON (Pin 8): On-Time Current Input. Tie a resistor from V IN
to this pin to set the one-shot timer current and thereby set
the switching frequency.
V FB1 (Pin 9): Error Amplifier Feedback Input. This pin
connects the error amplifier input to an external resistive
divider from V OUT .
SHDN (Pin 10): Shutdown, Active Low. Tie to 1V or more
to enable boost converter portion of the LTC3713. Ground
V FB2 (Pin 12): Boost Converter Feedback. The V FB2 pin is
connected to INTV CC through a resistor divider to set the
voltage on INTV CC . Set INTV CC voltage according to:
V INTVCC = 1.23V(1 + R F4 /R F3 )
SW2 (Pin 13): Boost Converter Switch Pin. Connect
inductor/diode for boost converter portion here. Minimize
trace area at this pin to keep EMI down.
PGND (Pins 14, 19): Power Ground. Connect these pins
closely to the source of the bottom N-channel MOSFET,
the (–) terminal of C VCC and the (–) terminal of C IN .
V IN2 (Pin 15): Input Supply Pin for Boost Converter
Portion of LTC3713. Must be locally bypassed.
V IN1 (Pin 16): Main Input Supply. Decouple this pin to
PGND with an RC filter (1 ? , 0.1 μ F).
INTV CC (Pin 17): Internal Regulator Output. The driver and
control circuits are powered from this voltage. Decouple
this pin to power ground with a minimum of 4.7 μ F low ESR
tantalum or ceramic capacitor.
BG (Pin 18): Bottom Gate Drive. Drives the gate of the
bottom N-channel MOSFET between ground and INTV CC .
SENSE – (Pin 20): Negative Current Sense Comparator
Input. The (–) input to the current comparator is normally
connected to power ground unless using a resistive di-
vider from INTV CC (see Applications Information).
SENSE + (Pin 21): Positive Current Sense Comparator
Input. The (+) input to the current comparator is normally
connected to the SW1 node unless using a sense resistor
(see Applications Information).
SW1 (Pin 22): Switch Node. The (–) terminal of the
bootstrap capacitor C B connects here. This pin swings
from a diode voltage drop below ground up to V IN .
TG (Pin 23): Top Gate Drive. Drives the top N-channel
MOSFET with a voltage swing equal to INTV CC superim-
posed on the switch node voltage SW1.
BOOST (Pin 24): Boosted Floating Driver Supply. The (+)
terminal of the bootstrap capacitor C B connects here. This
pin swings from a diode voltage drop below INTV CC up to
V IN + INTV CC .
to shut down.
3713fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| VE-27P-EW-F3 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27P-EW-F2 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27P-EW-F1 | CONVERTER MOD DC/DC 13.8V 100W |
| VE-27N-EY-B1 | CONVERTER MOD DC/DC 18.5V 50W |
| VE-27N-EW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3713EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3713EG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3713EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3714EG | 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3714EG#PBF | 功能描述:IC STP-DWN CNTRLR W/OPAMP 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。