- 您现在的位置：买卖IC网 > PDF目录44993 > LTC3810IG#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | LTC3810IG#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封装： | 5.30 MM, PLASTIC, SSOP-28 |
| 文件页数： | 13/36页 |
| 文件大小： | 495K |
| 代理商： | LTC3810IG#TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3810
20
3810fb
that have been surge tested for use in switching power
supplies. Several excellent surge-tested choices are the
AVX, TPS and TPSV or the KEMET T510 series. Aluminum
electrolytic capacitors have signicantly higher ESR, but
can be used in cost-driven applications providing that
consideration is given to ripple current ratings and long-
term reliability. Other capacitor types include Panasonic
SP and Sanyo POSCAPs.
Output Voltage
The LTC3810 output voltage is set by a resistor divider
according to the following formula:
VOUT = 0.8V 1+
RFB1
RFB2
The external resistor divider is connected to the output as
shown in the Functional Diagram, allowing remote voltage
sensing. The resultant feedback signal is compared with
the internal precision 800mV voltage reference by the
error amplier. The internal reference has a guaranteed
tolerance of <1%. Tolerance of the feedback resistors
will add additional error to the output voltage. 0.1% to
1% resistors are recommended.
Input Voltage Undervoltage Lockout
A resistor divider connected from the input supply to the
UVIN pin (see Functional Diagram) is used to program the
input supply undervoltage lockout thresholds. When the
rising voltage at UVIN reaches 0.88V, the LTC3810 turns
on, and when the falling voltage at UVIN drops below 0.8V,
the LTC3810 is shut down—providing 10% hysteresis.
The input voltage UVLO thresholds are set by the resistor
divider according to the following formulas:
VIN,FALLING = 0.8V 1+
RUV1
RUV2
and
VIN,RISING = 0.88V 1+
RUV1
RUV2
If input supply undervoltage lockout is not needed, it can
be disabled by connecting UVIN to INTVCC.
Top MOSFET Driver Supply (CB, DB)
An external bootstrap capacitor, CB, connected to the
BOOST pin supplies the gate drive voltage for the topside
MOSFET. This capacitor is charged through diode DB from
DRVCC when the switch node is low. When the top MOSFET
turns on, the switch node rises to VIN and the BOOST pin
rises to approximately VIN + INTVCC. The boost capacitor
needs to store about 100 times the gate charge required
by the top MOSFET. In most applications 0.1μF to 0.47μF,
X5R or X7R dielectric capacitor is adequate.
The reverse breakdown of the external diode, DB, must
be greater than VIN(MAX). Another important consideration
for the external diode is the reverse recovery and reverse
leakage, either of which may cause excessive reverse
current to ow at full reverse voltage. If the reverse cur-
rent times reverse voltage exceeds the maximum allow-
able power dissipation, the diode may be damaged. For
best results, use an ultrafast recovery diode such as the
MMDL770T1.
Bottom MOSFET Driver Return Supply (BGRTN)
The bottom gate driver, BG, switches from DRVCC to
BGRTN where BGRTN can be a voltage between ground
and –5V. Why not just keep it simple and always connect
BGRTN to ground? In high voltage switching converters,
the switch node dV/dt can be many volts/ns, which will
pull up on the gate of the bottom MOSFET through its
Miller capacitance. If this Miller current, times the internal
gate resistance of the MOSFET plus the driver resistance,
exceeds the threshold of the FET, shoot-through will oc-
cur. By using a negative supply on BGRTN, the BG can be
pulled below ground when turning the bottom MOSFET off.
This provides a few extra volts of margin before the gate
reaches the turn-on threshold of the MOSFET. Be aware
that the maximum voltage difference between DRVCC and
BGRTN is 14V. If, for example, VBGRTN = –2V, the maximum
voltage on DRVCC pin is now 12V instead of 14V.
IC/MOSFET Driver Supplies (INTVCC and DRVCC)
The LTC3810 drivers are supplied from the DRVCC and
BOOST pins (see Figure 3), which have an absolute maxi-
mum voltage of 14V. Since the main supply voltage, VIN
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3810EG | SWITCHING CONTROLLER, PDSO28 |
| LTC3812EFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812EFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3810IUH-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3810IUH-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EUHF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。