- 您现在的位置：买卖IC网 > PDF目录44993 > LTC3810IG#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | LTC3810IG#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封装： | 5.30 MM, PLASTIC, SSOP-28 |
| 文件页数： | 18/36页 |
| 文件大小： | 495K |
| 代理商： | LTC3810IG#TR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3810
25
3810fb
Feedback Component Selection
Selecting the R and C values for a typical Type 2 or Type 3
loop is a nontrivial task. The applications shown in this
data sheet show typical values, optimized for the power
components shown. They should give acceptable perfor-
mance with similar power components, but can be way off if
even one major power component is changed signicantly.
Applications that require optimized transient response will
require recalculation of the compensation values speci-
cally for the circuit in question. The underlying mathematics
are complex, but the component values can be calculated
in a straightforward manner if we know the gain and phase
of the modulator at the crossover frequency.
Modulator gain and phase can be obtained in one of
three ways: measured directly from a breadboard, or if
the appropriate parasitic values are known, simulated or
generated from the modulator transfer function. Mea-
surement will give more accurate results, but simulation
or transfer function can often get close enough to give
a working system. To measure the modulator gain and
phase directly, wire up a breadboard with an LTC3810
and the actual MOSFETs, inductor and input and output
capacitors that the nal design will use. This breadboard
should use appropriate construction techniques for high
speed analog circuitry: bypass capacitors located close
to the LTC3810, no long wires connecting components,
appropriately sized ground returns, etc. Wire the feedback
amplier with a 0.1μF feedback capacitor from ITH to FB
and a 10k to 100k resistor from VOUT to FB. Choose the
bias resistor (RB) as required to set the desired output
voltage. Disconnect RB from ground and connect it to
a signal generator or to the source output of a network
analyzer to inject a test signal into the loop. Measure the
gain and phase from the ITH pin to the output node at the
positive terminal of the output capacitor. Make sure the
analyzer’s input is AC coupled so that the DC voltages
present at both the ITH and VOUT nodes don’t corrupt the
measurements or damage the analyzer.
If breadboard measurement is not practical, a SPICE
simulation can be used to generate approximate gain/
phase curves. Plug the expected capacitor, inductor
and MOSFET values into the following SPICE deck and
generate an AC plot of VOUT/VITH with gain in dB and
phase in degrees. Refer to your SPICE manual for details
of how to generate this plot.
*3810 modulator gain/phase
*2006 Linear Technology
*this le simulates a simplied model of
*the LTC3810 for generating a v(out)/v(ith)
*bode plot
.param rdson=.0135 ;MOSFET rdson
.param Vrng=2
;use 1.4 for INTVCC and
0.7 for ground
.param vsnsmax={0.173*Vrng-0.026}
.param Imax={vsnsmax/rdson}
.param DL=4
;inductor ripple current
*inductor current
gl out 0 value={(v(ith)-1.2)*Imax/1.2+DL/2}
*output cap
cout out out2 270u ;capacitor value
resr out2 0 0.018 ;capacitor ESR
*load
Rout out 0 2 ; load resistor
vstim ith 0 0 ac 1 ;ac stimulus
.ac dec 100 100 10meg
.probe
.end
Mathematical software such as MATHCAD or MATLAB
can also be used to generate plots using the following
transfer function of the modulator:
H(s)
=
VSENSE(MAX)
1.2 RDS(ON)
1
+ sR
ESR COUT
1
+ sR
L COUT
RL
s
= j2 f
(2)
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3810EG | SWITCHING CONTROLLER, PDSO28 |
| LTC3812EFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812EFE-5#TR | 1 A SWITCHING CONTROLLER, PDSO16 |
| LTC3812IFE-5 | 1 A SWITCHING CONTROLLER, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3810IUH-5#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3810IUH-5#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3811EUHF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。