参数资料
型号: LTC3828EUH#TRPBF
厂商: Linear Technology
文件页数: 25/32页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 32-QFN
标准包装: 2,500
系列: PolyPhase®
PWM 型: 电流模式
输出数: 2
频率 - 最大: 590kHz
占空比: 99.4%
电源电压: 4.5 V ~ 28 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 32-WFQFN 裸露焊盘
包装: 带卷 (TR)
LTC3828
APPLICATIONS INFORMATION
( 5 ) 2 [ 1 + ( 0 . 005 )( 50 ° C – 25 ° C ) ] ?
P MAIN =
? 5 – 2 . 3 + 2 . 3 ? ( ) = 332 mW
? 1 1 ?
I SC =
? = 2 . 1 A
– ?
1 .8V
22 V
( 0 . 035 Ω ) + ( 22 V ) 2 ? ? ? 52 A ? ? ? ( 4 Ω )( 215 pF ) ?
300 kHz
? ?
A short-circuit to ground will result in a folded back cur-
rent of:
25mV  1 ? 120 ns ( 22 V ) ?
0 . 01 Ω 2 ? 3 . 3 μ H ?
with a typical value of R DS(ON) and δ = (0.005/°C)(20) =
0.1. The resulting power dissipated in the bottom MOSFET
is:
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return of
C INTVCC must return to the combined C OUT (–) terminals.
The path formed by the top N-channel MOSFET, Schottky
diode and the C IN capacitor should have short leads and
PC trace lengths. The output capacitor (–) terminals should
be connected as close as possible to the (–) terminals
of the input capacitor by placing the capacitors next to
each other and away from the Schottky loop described
above.
3. Do the LTC3828 V OSENSE pins’ resistive dividers connect
to the (+) terminals of C OUT ? The resistive divider must
be connected between the (+) terminal of C OUT and signal
ground. The R2 and R4 connections should not be along
the high current input feeds from the input capacitor(s).
4. Are the SENSE – and SENSE + leads routed together with
( ) ( ) ( )
1 . 125 0 . 022 Ω
2 . 1 A
P SYNC =
22V – 1 .8V
22 V
2
minimum PC trace spacing? The ?lter capacitor between
SENSE + and SENSE – should be as close as possible to
= 100 mW
which is less than under full-load conditions.
C IN is chosen for an RMS current rating of at least 3A at
temperature assuming only this channel is on. C OUT is
chosen with an ESR of 0.02Ω for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
V ORIPPLE = R ESR ( Δ I L ) = 0.02Ω(1.67A) = 33mV P-P
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layout diagram of Figure 12. The Figure 13 illustrates the
current waveforms present in the various branches of the
2-phase synchronous regulators operating in the continu-
ous mode. Check the following in your layout:
1. Are the top N-channel MOSFETs M1 and M3 located
within 1cm of each other with a common drain connection
the IC. Ensure accurate current sensing with Kelvin con-
nections at the SENSE resistor.
5. Is the INTV CC decoupling capacitor connected close to
the IC, between the INTV CC and the power ground pins?
This capacitor carries the MOSFET drivers current peaks.
An additional 1μF ceramic capacitor placed immediately
next to the INTV CC and PGND pins can help improve noise
performance substantially.
6. Keep the switching nodes (SW1, SW2), top gate nodes
(TG1, TG2), and boost nodes (BOOST1, BOOST2) away
from sensitive small-signal nodes, especially from the
opposites channel’s voltage and current sensing feedback
pins. All of these nodes have very large and fast moving
signals and therefore should be kept on the “output side”
of the LTC3828 and occupy minimum PC trace area.
7. Use a modi?ed “star ground” technique: a low imped-
ance, large copper area central grounding point on the same
side of the PC board as the input and output capacitors with
tie-ins for the bottom of the INTV CC decoupling capacitor,
the bottom of the voltage feedback resistive divider and
the SGND pin of the IC.
at CIN? Do not attempt to split the input decoupling for
the two channels as it can cause a large resonant loop.
3828fc
25
相关PDF资料
PDF描述
LTC3829EFE#PBF IC REG CTRLR BUCK PWM CM 38TSSOP
LTC3830ES8#PBF IC REG CTRLR BUCK PWM VM 8-SOIC
LTC3831EGN IC SW REG CONTROLLR SYNC 16-SSOP
LTC3832-1ES8#PBF IC REG CTRLR BUCK PWM VM 8-SOIC
LTC3833EFE#PBF IC REG CTRLR BUCK PWM CM 20TSSOP
相关代理商/技术参数
参数描述
LTC3829EFE#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
LTC3829EFE#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3829EUHF#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3829EUHF#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3829IFE#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX