参数资料
型号: LTC3855IFE#PBF
厂商: Linear Technology
文件页数: 14/44页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 38-SSOP
标准包装: 50
系列: PolyPhase®
PWM 型: 电流模式
输出数: 2
频率 - 最大: 850kHz
占空比: 95%
电源电压: 4.5 V ~ 38 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 38-TFSOP (0.173",4.40mm 宽)裸露焊盘
包装: 管件
LTC3855
OPERATION
V SENSEMAX ( ADJ ) = V SENSE ( MAX ) ?
SensingtheOutputVoltagewithaDifferential
Amplifier
The LTC3855 includes a low offset, unity gain, high band-
width differential amplifier for applications that require true
remote sensing. Sensing the load across the load capaci-
tors directly greatly benefits regulation in high current, low
voltage applications, where board interconnection losses
can be a significant portion of the total error budget.
The LTC3855 differential amplifier has a typical output slew
rate of 2V/μs. The amplifier is configured for unity gain,
meaning that the difference between DIFFP and DIFFN is
translated to DIFFOUT, relative to SGND.
Care should be taken to route the DIFFP and DIFFN PCB
traces parallel to each other all the way to the terminals
of the output capacitor or remote sensing points on the
board. In addition, avoid routing these sensitive traces
near any high speed switching nodes in the circuit. Ideally,
the DIFFP and DIFFN traces should be shielded by a low
impedance ground plane to maintain signal integrity.
Inductor DCR Sensing Temperature Compensation and
the ITEMP Pins
Inductor DCR current sensing provides a lossless method
of sensing the instantaneous current. Therefore, it can
provide higher efficiency for applications of high output
currents. However the DCR of a copper inductor typically
has a positive temperature coefficient. As the temperature
of the inductor rises, its DCR value increases. The current
limit of the controller is therefore reduced.
LTC3855 offers a method to counter this inaccuracy by
allowing the user to place an NTC temperature sensing
resistor near the inductor. ITEMP pin, when left floating, is
at a voltage around 5V and DCR temperature compensa-
tion is disabled. ITEMP pin has a constant 10μA precision
current flowing out the pin. By connecting an NTC resistor
from ITEMP pin to SGND, the maximum current sense
threshold can be varied over temperature according the
following equation:
1. 8 – V ITEMP
1 . 3
Where:
V SENSEMAX(ADJ) is the maximum adjusted current sense
threshold.
V SENSE(MAX) is the maximum current sense threshold
specified in the electrical characteristics table. It is typi-
cally 75mV, 50mV, or 30mV depending on the setting
I LIM pins.
V ITEMP is the voltage of ITEMP pin.
The valid voltage range for DCR temperature compensa-
tion on the ITEMP pin is between 0.5V to 0.2V, with 0.5V
or above being no DCR temperature correction and 0.2V
the maximum correction. However, if the duty cycle of the
controller is less than 25%, the ITEMP range is extended
from 0.5V to 0V.
An NTC resistor has a negative temperature coefficient,
that means that its value decreases as temperature rises.
The V ITEMP voltage, therefore, decreases as temperature
increases and in turn the V SENSEMAX(ADJ) will increase to
compensate the DCR temperature coefficient. The NTC
resistor, however, is non-linear and user can linearize its
value by building a resistor network with regular resis-
tors. Consult the NTC manufacture datasheets for detailed
information.
Another use for the ITEMP pins, in addition to NTC com-
pensated DCR sensing, is adjusting V SENSE(MAX) to values
between the nominal values of 30mV, 50mV and 75mV for
a more precise current limit. This is done by applying a
voltage less than 0.5V to the ITEMP pin. V SENSE(MAX) will
be varied per the above equation and the same duty cycle
limitations will apply. The current limit can be adjusted using
this method either with a sense resistor or DCR sensing.
For more information see the NTC Compensated DCR Sens-
ing paragraph in the Applications Information section.
Frequency Selection and Phase-Locked Loop
(FREQ and MODE/PLLIN Pins)
The selection of switching frequency is a trade-off between
efficiency and component size. Low frequency opera-
tion increases efficiency by reducing MOSFET switching
losses, but requires larger inductance and/or capacitance
to maintain low output ripple voltage. The switching
3855f
  
相关PDF资料
PDF描述
VI-25K-EY-B1 CONVERTER MOD DC/DC 40V 50W
LT3724IFE#TRPBF IC REG CTRLR BST INV PWM 16TSSOP
VI-25K-EW-F4 CONVERTER MOD DC/DC 40V 100W
LT3800IFE#TRPBF IC REG CTRLR INV PWM CM 16-TSSOP
VI-25K-EW-F3 CONVERTER MOD DC/DC 40V 100W
相关代理商/技术参数
参数描述
LTC3855IUJ#PBF 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR
LTC3855IUJ#PBF-ES 制造商:Linear Technology 功能描述:
LTC3855IUJ#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3856EFE#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38TFSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP(0.173",4.40mm 宽) 包装:带卷 (TR)
LTC3856EFE#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)