- 您现在的位置：买卖IC网 > PDF目录1833 > LTC3867EUF#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 24-QFN PDF资料下载
参数资料
| 型号： | LTC3867EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-QFN |
| 产品培训模块： | LTC3867 Synchronous Step-Down DC/DC Controller |
| 标准包装： | 91 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.2MHz |
| 占空比： | 98% |
| 电源电压： | 4 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3867
APPLICATIONS INFORMATION
? V SENSE =
20°C.Increasethisvaluetoaccountforthetemperature
coefficient of resistance, which is approximately 0.4%/°C.
A conservative value for T L(MAX) is 100°C. To scale the
maximum inductor DCR to the desired sense resistor
value, use the divider ratio:
less than 40%. For a DCR sensing application, the actual
ripple voltage will be determined by the equation:
V IN ? V OUT V OUT
R1 ? C1 V IN ? f OSC
R D =
R SENSE(EQUIV)
DCR (MAX) at T L(MAX)
Inductor DCR Sensing Temperature Compensation
and the ITEMP Pin
R1||R2 =
R1 =
, R2 =
( V IN(MAX) ? V OUT ) ? V OUT
P LOSS R1 =
V ITEMP
2.8
V SENSEMAX(ADJ) = V SENSE(MAX) ?
C1 is usually selected to be in the range of 0.047μF to
0.47μF. This forces R1|| R2 to around 2k, reducing error
that might have been caused by the SENSE + pin’s ±1μA
current. T L(MAX) is the maximum inductor temperature.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
L
(DCR at 20 ° C) ? C1
The sense resistor values are:
R1|| R2 R1 ? R D
R D 1 ? R D
The LTC3867 also features a DCR temperature compen-
sation circuit that uses an NTC temperature sensor. See
the Inductor DCR Sensing Temperature Compensation
section for details.
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor, due
to the extra switching losses incurred through R1. However,
DCR sensing eliminates a sense resistor, reduces conduc-
tion losses and provides higher efficiency at heavy loads.
Peak efficiency is about the same with either method. To
maintain a good signal-to-noise ratio for the current sense
signal, use a minimum ? V SENSE of 10mV for duty cycles
Inductor DCR current sensing provides a lossless method
of sensing the instantaneous current. Therefore, it can
provide higher efficiency for applications of high output
currents. However, the DCR of the inductor, which is the
small amount of DC winding resistance of the copper,
typically has a positive temperature coefficient. As the
temperature of the inductor rises, its DCR value increases.
The current limit of the controller is therefore reduced.
The LTC3867 offers a method to counter this inaccuracy
by allowing the user to place an NTC temperature sensing
resistor near the inductor to actively correct this error. The
ITEMP pin, when left floating, is at a voltage around 5V and
DCR temperature compensation is disabled. The ITEMP
pin has a constant 30μA precision current flowing out the
pin. By connecting an NTC resistor from the ITEMP pin
to SGND, the maximum current sense threshold can be
varied over temperature according the following equation:
1.8 –
1.3
where:
V SENSEMAX(ADJ) is the maximum adjusted current sense
threshold.
V SENSE(MAX) is the maximum current sense threshold
specified in the Electrical Characteristics table. It is
typically 75mV, 60mV, 50mV, 40mV or 30mV depending
on the setting I LIM pins.
V ITEMP is the voltage of the ITEMP pin.
The valid voltage range for DCR temperature compensation
on the ITEMP pin is 1.4V to 0.6V, with 1.4V or above being
no DCR temperature correction and 0.6V the maximum
correction. However, if the duty cycle of the controller is less
than 25%, the ITEMP range is extended from 1.4V to 0V.
3867f
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3868EUFD-1#PBF | IC REG CTRLR BUCK PWM CM 28-QFN |
| LTC3869EUFD#PBF | IC REG CTRLR BUCK PWM CM 28-QFN |
| LTC3872ETS8#TRMPBF | IC REG CTRLR BST PWM CM TSOT23-8 |
| LTC3873EDDB#TRMPBF | IC REG CTRLR BST FLYBK PWM 8-DFN |
| LTC3873ITS8-5#TRPBF | IC REG CTRLR BST FLYBK TSOT23-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3867IUF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3867IUF#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EGN-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EUFD-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。