- 您现在的位置：买卖IC网 > PDF目录1833 > LTC3867EUF#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 24-QFN PDF资料下载
参数资料
| 型号： | LTC3867EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 31/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-QFN |
| 产品培训模块： | LTC3867 Synchronous Step-Down DC/DC Controller |
| 标准包装： | 91 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.2MHz |
| 占空比： | 98% |
| 电源电压： | 4 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页
LTC3867
APPLICATIONS INFORMATION
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layout diagram of Figure 16. Check the following in the
PC layout:
1. The INTV CC decoupling capacitor should be placed
immediately adjacent to the IC between the INTV CC pin
and PGND plane. A 1μF ceramic capacitor of the X7R
or X5R type is small enough to fit very close to the IC
to minimize the ill effects of the large current pulses
drawn to drive the bottom MOSFETs. An additional
4.7μF to 10μF of ceramic, tantalum or other very low
ESR capacitance is recommended in order to keep the
internal IC supply quiet.
2. Place the feedback divider between the + and – terminals
of COUT. Route DIFF + and DIFF – with minimum PC trace
spacing from the IC to the feedback divider.
3. Are the SENSE + and SENSE – printed circuit traces
routed together with minimum PC trace spacing? The
filter capacitors between SENSE + and SENSE – should
be as close as possible to the pins of the IC. Connect
the SENSE + and SENSE – pins to the pads of the sense
resistor as illustrated in Figure 2.
4. Do the (+) plates of C IN connect to the drain of the
topside MOSFET as closely as possible? This capacitor
provides the pulsed current to the MOSFET.
5. Keep the switching nodes, SW, BOOST and TG away
from sensitive small-signal nodes (SENSE + , SENSE – ,
DIFF + , DIFF – , V FB ). Ideally the SW, BOOST and TG printed
circuit traces should be routed away and separated from
the IC and especially the quiet side of the IC. Separate
the high dv/dt traces from sensitive small-signal nodes
with ground traces or ground planes.
6. Use a low impedance source such as a logic gate to
drive the MODE/PLLIN pin and keep the lead as short
as possible.
7. The 47pF to 330pF ceramic capacitor between the I TH
pin and signal ground should be placed as close as
possible to the IC. Figure 16 illustrates all branch cur-
rents in a switching regulator. It becomes very clear
after studying the current waveforms why it is critical to
keep the high switching current paths to a small physical
size. High electric and magnetic fields will radiate from
these loops just as radio stations transmit signals. The
output capacitor ground should return to the negative
terminal of the input capacitor and not share a com-
mon ground path with any switched current paths. The
left half of the circuit gives rise to the noise generated
by a switching regulator. The ground terminations of
the synchronous MOSFET and Schottky diode should
return to the bottom plate(s) of the input capacitor(s)
with a short isolated PC trace since very high switched
currents are present. External OPTI-LOOP ? compensa-
tion allows overcompensation for PC layouts which are
not optimized but this is not the recommended design
procedure.
V IN
L1
V OUT
R IN
+
C IN
SW2
D1
SW1
R SENSE
C OUT
+
R L
3867 F16
BOLD LINES INDICATE HIGH, SWITCHING CURRENTS. KEEP LINES TO A MINIMUM LENGTH
Figure 16. Branch Current Waveforms
3867f
31
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3868EUFD-1#PBF | IC REG CTRLR BUCK PWM CM 28-QFN |
| LTC3869EUFD#PBF | IC REG CTRLR BUCK PWM CM 28-QFN |
| LTC3872ETS8#TRMPBF | IC REG CTRLR BST PWM CM TSOT23-8 |
| LTC3873EDDB#TRMPBF | IC REG CTRLR BST FLYBK PWM 8-DFN |
| LTC3873ITS8-5#TRPBF | IC REG CTRLR BST FLYBK TSOT23-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3867IUF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3867IUF#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EGN-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3868EUFD-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。